Answer:
The flow is turbulent at both the parts of the tube.
Explanation:
Given:
Water is flowing in circular tube.
Inlet diameter is [tex]d_{1}= 2[/tex]m.
Outlet diameter is [tex]d_{2}= 3[/tex]m.
Inlet velocity is [tex]V_{1}= 3[/tex] m/s.
Kinematic viscosity is [tex]\nu =1.24\times 10^{-6}[/tex] m²/s.
Concept:
Apply continuity equation to find the velocity at outlet.
Apply Reynolds number equation for flow condition.
Step1
Apply continuity equation for outlet velocity as follows:
[tex]A_{1}V_{1}=A_{2}V_{2}[/tex]
[tex]\frac{\pi}{4}d^{2}_{1}V_{1}=\frac{\pi}{4}d^{2}_{2}V_{2}[/tex]
Substitute the values in the above equation as follows:
[tex]\frac{\pi}{4}2^{2}\times 3=\frac{\pi}{4}3^{2}V_{2}[/tex]
[tex]2^{2}\times 3=3^{2}V_{2}[/tex]
[tex]V_{2}=\frac{4}{3}[/tex] m/s.
Step2
Apply Reynolds number formula for the flow condition at inlet as follows:
[tex]Re=\frac{v_{1}d_{1}}{\nu }[/tex]
[tex]Re=\frac{2\times 3}{1.24\times 10^{-6}}[/tex]
Re=4838709.677
Apply Reynolds number formula for the flow condition at outlet as follows:
[tex]Re=\frac{v_{2}d_{2}}{\nu }[/tex]
[tex]Re=\frac{\frac{4}{3}\times 3}{1.24\times 10^{-6}}[/tex]
Re=3225806.452
Thus, the Reynolds number is greater than 2000. Hence the flow is turbulent.
Hence, the flow is turbulent at both the parts of the tube.
The horizontal component of acceleration, ay during a projectile motion is usually assumed to be_________ a)-9.81 m/s^2 b)-Zero c)- Constant d)- 32.2 m/s^2
Answer:
b) zero
Explanation:
The horizontal component of acceleration during projectile motion is usually assumed to be zero.Because in projectile motion horizontal component of velocity will remain the constant and we know that rate of change of velocity with time is called acceleration.So when velocity is constant then acceleration will be zero.
In projectile motion ,gravitational acceleration will be in only vertical direction.
What % of Nickel is needed to increase toughness?
Answer:
2% to 20% Ni
Explanation:
If we will talk about steel then ,for increasing the toughness property of steel generally 2% to 20% Ni added .Ni also increase resistance to corrosion and oxidation, impact strength and strength.
We know that steel is an alloy of iron and carbon.But to improve the property of steel different alloying elements added by this steel become desirable to use at different situations.
Please define the coefficient of thermal expansion?
Answer:
The coefficient of thermal expansion tells us how much a material can expand due to heat.
Explanation:
Thermal expansion occurs when a material is subjected to heat and changes it's shape, area and volume as a result of that heat. How much that material changes is dependent on it's coefficient of thermal expansion.
Different materials have different coefficients of thermal expansion (i.e. It is a material property and differs from one material to the next). It is important to understand how materials behave when heated, especially for engineering applications when a change in dimension might pose a problem or risk (eg. building large structures).
What is the movement of the piston from top dead center (TDC) to bottom dead center (BDC) called?
Answer:
Piston movement of TDC to BDC is called stroke.
Explanation:
Step1
In any engine fuel is burned inside the cylinder and forces the piston to move from top dead center to bottom dead center. First piston is moved from top dead center to bottom dead center to allow the suction of fuel inside the cylinder. Then piston move toward top dead center and compresses the fuel. This process is called compression of fuel. Then fuel is burned with the spark inside the cylinder and the piston moves toward bottom dead center. This process is called expansion process. Last process is the expansion process that allows the exhaust out of the cylinder.
Step2
The piston reciprocates from bottom position of the cylinder to top position of the cylinder and vice versa. So, the motion of piston from top center to bottom center is called stroke. One movement of piston from TDC to BDC is called one stroke. There are total four strokes in petrol engine and diesel engine. So, two strokes are equal to one cycle or one rotation of crank and four strokes are equal to two rotation of crank.
Thus, piston movement of TDC to BDC is called stroke.
Answer:
The return stroke
Explanation:
Motion from top dead center to bottom dead center is called the return stroke because motion from the bottom to the top is the forward stroke.
You want a pot of water to boil at 105celcius. How heavy a
lid should you put on the 15 cm diameterpot when Patm =
101 kPa?
Answer:
36 kg
Explanation:
For water to boil at 105 C it needs a pressure of 121 kPa (this is the vapor pressure of water at 105 C).
In the lid there will be a difference of pressure from one side to the other, this will be compensated by the weight of the lid.
Δp = pwater - patm
Δp = 121 - 101 = 20 kPa
The pressure caused by the weigh of the lid is:
Δp = w / A
Δp = m * g / A
Rearranging
m = Δp * A / g
m = Δp * π/4 * d^2 / g
m = 20000 * π/4 * 0.15^2 / 9.81 = 36 kg
Sketch the velocity profile for laminar and turbulent flow.
Answer:
The laminar flow is generally given in high viscosity fluids such as honey or oil, it has the characteristic of flowing in an orderly manner, the walls of the tube have a zero speed while in the center it has a maximum speed.
turbulent flow is characterized by fluid velocity vectors presenting themselves in a disorderly manner and in all directions.
I attached the drawings for the velocity profile in laminar and turbulent flow.
The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero.
Answer:
Zero.
Explanation:
Lets take velocity V is given as in 2 dimensional flow
V=u i +v j
V=f(x,y)
u=f(x,y)
v=f(x,y)
Rotational ability ω given as
[tex]\omega =\dfrac{1}{2}\left (\dfrac{\partial v}{\partial x}-\dfrac{\partial u} {\partial x}\right)[/tex]
If
ω=0 ,then flow will be irrotational.
ω ≠0 ,then flow will be rotational.
So we can say that , ω will be zero every where for irrotational two dimensional flow .
Polymers can be natural or synthetic. a)-True b)- false?
Answer:
TRUE
Explanation:
Polymers can be natural as well as synthetic
The polymer which are found in nature are called natural polymer tease polymer are not synthesized, they are found in nature
Example of natural polymers is cellulose, proteins etc
On the other hand synthetic polymers are not found in nature they are synthesized in market
There are many example of synthetic polymer
Example : nylon, Teflon etc
So it is a true statement
The energy conversion that takes place in an evaporative cooler is: a. thermal energy to chemical energy b. thermal energy to heat c. cooling of thermal energy d. heat energy to mechanical energy
Answer:
C.Cooling of thermal energy
Explanation:
In evaporative cooling liquid water convert into vapor by using thermal energy.In this out side air is used to evaporate the water.
Hot air enters from outside and this hot air gets contact with wet matrix .In wet matrix temperature of air will reduce and temperature of water will increases .After wet matrix heat transfer take place between air and water .After that by using force convection air pushed out and produce cooling.
Ignoring any losses, estimate how much energy (in units of Btu) is required to raise the temperature of water in a 90-gallon hot-water tank from 60°F to 110°F. The specific heat of water is approximated as a constant, whose value is 0.999 Btu/·lbmR at the average temperature of (60 + 110)/2 = 85ºF. In fact, c remains constant at 0.999 Btu/lbm·R (to three digits) from 60ºF to 110ºF. For this same temperature range, the density varies from 62.36 lbm/ft3 at 60ºF to 61.86 lbm/ft3 at 110ºF. We approximate the density as remaining constant, whose value is 62.17 lbm/ft3 at the average temperature of 85ºF.
Answer:
Q=36444.11 Btu
Explanation:
Given that
Initial temperature = 60° F
Final temperature = 110° F
Specific heat of water = 0.999 Btu/lbm.R
Volume of water = 90 gallon
Mass = Volume x density
[tex]1\ gallon = 0.13ft^3[/tex]
Mass ,m= 90 x 0.13 x 62.36 lbm
m=729.62 lbm
We know that sensible heat given as
Q= m Cp ΔT
Now by putting the values
Q= 729.62 x 0.999 x (110-60) Btu
Q=36444.11 Btu
The searchlight on the boat anchored 2000 ft from shore
isturned on the automobile, which is traveling along the
straightroad at a constant speed of 80 ft/s. Determine the
angularrate of rotation of the light when the automobile is r =
3000 ftfrom the boat.
The angular speed of a flywheel rotating at 300 revolutions per minute is calculated by converting revolutions to radians and minutes to seconds, resulting in an angular speed of 10π rad/s.
Explanation:The question asks to determine the angular rate of rotation of a searchlight on a boat when targeting an automobile that is 3000 ft away and moving at 80 ft/s. This involves understanding the relationship between linear velocity, radius, and angular velocity, which is a crucial concept in trigonometry and physics.
To find the angular speed of the flywheel rotating at 300 revolutions per minute, we first convert revolutions per minute (rpm) to radians per second, knowing that one revolution is 2π radians and there are 60 seconds in a minute. Therefore:
Angular speed = 300 rpm × (2π radians/revolution) × (1 minute/60 seconds) = 300 × 2π / 60 rad/s = 10π rad/s.
When a 20-lb weight is suspended from a spring, the spring is stretched a distance of 1 in. Determine the natural frequency and the period of vibration for a 30-lb weight attached to the same spring
Answer:
natural frequency = 2.55 Hz
period of vibration = 0.3915 s
Explanation:
given data
weight = 20 lb
distance = 1 in = [tex]\frac{1}{12}[/tex] ft
weight = 30 lb
to find out
Determine the natural frequency and the period of vibration
solution
we first calculate here stiffness k by given formula that is
k = [tex]\frac{weight}{diatnace}[/tex] ..........1
k = [tex]\frac{20}{1/12}[/tex]
k = 240 lb/ft
so
frequency = [tex]\sqrt{\frac{k}{m} }[/tex] ..................2
put here value k and mass m = [tex]\frac{weight}{g}[/tex]
frequency = [tex]\sqrt{\frac{240}{30/32.2} }[/tex]
frequency = 16.05 rad/s
and
period of vibration = [tex]\frac{2* \pi }{frequency}[/tex]
period of vibration = [tex]\frac{2* \pi }{16.05}[/tex]
period of vibration = 0.3915 s
and
natural frequency = [tex]\frac{1 }{period of vibration}[/tex]
natural frequency = [tex]\frac{1 }{0.3915}[/tex]
natural frequency = 2.55 Hz
A(n)______topology is a mixture of more than one type of topology.
Answer:
Hybrid topology is the connection of one or more than one topology.
Explanation:
Topology:
Topology is the arrangement of network.These network connects by line and nodes.
Type of topology:
1.Bus topology
2.Star topology
3.Ring topology
4.Mesh topology
Along with given above topology one topology is also used is known as hybrid topology.Hybrid topology is the connection of one or more than two one above given topology.
A 15-mm-diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 30°, what must be the length of the bar?
Answer:
The length of bar will be 2.82 m
Explanation:
Given that
d= 15 mm
r= 7.5 mm
Shear stress = 110 MPa
θ = 30° (30° = 30° x π/180° =0.523 rad)
θ = 0.523 rad
G for steel
G= 79.3 GPa
We know that
[tex]\dfrac{\tau}{r}=\dfrac{G\theta }{L}[/tex]
[tex]\dfrac{110}{7.5\times 10^{-3}}=\dfrac{79.3\times 10^3\times 0.523 }{L}[/tex]
L= 2. 82 m
The length of bar will be 2.82 m
2.4 kg of nitrogen at an initial state of 285K and 150 kPa is compressed slowly in an isothermal process to a final pressure of 600 kPa. Determine the work.
Answer:
W=-280.67 KJ
Explanation:
Given that
Initial pressure = 150 KPa
Final pressure = 600 KPa
Temperature T= 285 K
Mass m=2.4 Kg
We know that ,work in isothermal process given as
[tex]W=mRT\ ln\dfrac{P_1}{P_2}[/tex]
Gas constant for nitrogen gas R=0.296 KJ/kgK
Now by putting the values
[tex]W=mRT\ ln\dfrac{P_1}{P_2}[/tex]
[tex]W=2.4\times 0.296\times 285\ ln\dfrac{150}{600}[/tex]
W=-280.67 KJ
Negative sign indicates that it is compression process and work is done on the gas.
A car starts out from rest (zero velocity) at an elevation of 500 m and drives up a hill to reach a final elevation of 2000m and a final velocity of 20 m/s. At the same time the entire car heats up so the Internal Energy of the car increases by 100 kJ. What is the total energy change of the car if its mass is 2000 kg?
Answer:29,930 kJ
Explanation:
Given
Car starts with an initial elevation of 500 m and drives up a hill to reach a final elevation of 2000 m
Final velocity (V)=20 m/s
Energy of car increases by 100 kJ
mass of car(m)=2000 kg
[tex]Total Energy =\Delta PE+\Delta KE+\Delta U[/tex]
[tex]\Delta PE=mg(\Delta h)=2000\times 9.81\times (2000-500)[/tex]
[tex]\Delta PE=29,430 kJ[/tex]
[tex]\Delta KE=m\frac{v_2^2-v_1^2}{2}[/tex]
[tex]\Delta KE=2000\times \frac{20^2-0^2}{2}[/tex]
[tex]\Delta KE=400 kJ[/tex]
[tex]\Delta U=100 kJ[/tex]
Total Energy=29,430+400+100=29,930 kJ
A cylindrical specimen of some metal alloy having an elastic modulus of 126 GPa and an original cross-sectional diameter of 4.0 mm will experience only elastic deformation when a tensile load of 2380 N is applied. Calculate the maximum length of the specimen before deformation if the maximum allowable elongation is 0.44 mm.
Answer:
The maximum length of the specimen is 0.2927 m or 292.7 mm
Solution:
Modulus of elasticity, E = 126 GPa = [tex]126\times 10^{9}[/tex]
Diameter of the cross-section, D = 4.0 mm = [tex]4.0\times 10^{- 3} m[/tex]
Force due to tension, F = 2380 N
Maximum elongation, [tex]\Delta L = 0.44 mm = 0.44\times 10^{- 3} m[/tex]
Now,
The maximum length of the specimen, [tex]L_{m}[/tex] can be calculated as follows:
The cross-sectional area, [tex]A_{c} = \frac{\pi D^{2}}{4} = \frac{\pi\times (4.0\times 10^{- 3})^{2}}{4} = 1.256\times 10^{- 5} m^{2}[/tex]
Now, the stress on the specimen, [tex]\sigma_{s} = \frac{F}{A_{c}} = \frac{2380}{1.256+\times 10^{- 5}}[/tex]
[tex]\sigma_{s} = 1.89\times 10^{8} N/m^{2}[/tex]
Now,
The strain on the specimen, [tex]\epsilon_{s}[/tex]:
[tex]\epsilon_{s} = \frac{\Delta L}{L_{m}}[/tex]
Also, from Hooke's law:
[tex]E = \frac{\sigma_{s}}{epsilon_{s}}[/tex]
⇒ [tex]E = \frac{1.89\times 10^{8}}{\frac{\Delta L}{L_{m}}}[/tex]
⇒ [tex]L_{m} = \frac{\Delta Ltimes E}{1.89\times 10^{8}}[/tex]
⇒ [tex]L_{m} = \frac{0.44\times 10^{- 3}\times 126\times 10^{9}}{1.89\times 10^{8}} = 0.2927 m[/tex]
The maximum length of the specimen before deformation is: 292.72 mm (0.2927 m).
Tensile PropertiesFor solving this question, it's necessary to know some concepts about the material's properties.
The tensile stress (σ) is determined from the ratio between load and original area before the load applied (σ=[tex]\frac{F}{Ao}[/tex]). Depending on the load applied, the material can have an elastic deformation (temporary deformation) and plastic deformation (permanent deformation). Both deformations can be calculated by the equation: ε=ΔL/Lo, where ΔL= deformation elongation and Lo= the original length before the load applied.
Elastic DeformationWhen the material is in the elastic portion, there is a linear relationship between stress and strain given by: σ=Eε. Due to this relationship, it is possible to find the elastic deformation (ε) when we know the stress (σ) and elastic modulus (E).
Now you have the necessary information to solve your question.
The question gives:
E (elastic modulus) =126 GPA
d (original cross-sectional diameter)=4 mm
F (tensile load)=2380 N
ΔL (maximum allowable elongation) =0.44 mm
1. Find the area of the cylindrical specimen.
[tex]Ao=\frac{\pi *d^2}{4} =\frac{\pi *4^2}{4}=\pi *4=12.57 mm^2[/tex]2. Find the tensile stress.
σ= [tex]\frac{F}{Ao} =\frac{2380 N }{12.57 mm^2} =189.39 MPa[/tex]
3. Calculate the maximum length of the specimen before deformation.
Knowing that ε=ΔL/Lo and σ=Eε, you can rewrite these equations as:
σ= E * (ΔL/Lo)
σ= (E * ΔL)/Lo
The question asks the maximum length of the specimen before deformation, therefore you should find Lo. Thus,
Lo= (E * ΔL)/σ
[tex]Lo=\frac{126*10^3 MPa*0.44 mm}{189.39 MPa} =292.72 mm= 0.2927 m[/tex]
Read more about the tensile stress here:
https://brainly.com/question/19756298
Describe the cartesain coordinate system.
Answer:
Cartesian coordinate system is used to specify any point on a plane.
In two dimensional plane,the two types of axes or coordinates are [tex]x[/tex] and [tex]y[/tex] axis.
Explanation:
Cartesian coordinate system specifies each point and every point on axes.
A Cartesian Coordinate system in two dimension also named as rectangular coordinate system.
The two types of axes or coordinates are [tex]x[/tex] and [tex]y[/tex] axis.
The horizontal axis is [tex]x[/tex]-axis and vertical axis is named as [tex]y[/tex]-axis.
The coordinate system specifies each point as a set of numerical coordinates in a plane which are signed from negative to positive. that is from ([tex]-\infty[/tex],[tex]\infty[/tex]).
In three dimensional plane, [tex]x[/tex], [tex]y[/tex] and [tex]z[/tex] coordinates are used and in two dimensional plane, [tex]x[/tex] and [tex]y[/tex]coordinates are used to address any point in the interval ([tex]-\infty[/tex],[tex]\infty[/tex]).
For defining both the coordinates, the two perpendicular directed lines [tex]x[/tex]- axis and [tex]x[/tex]-axis are drawn.
Now, for example [tex](3,4)[/tex] is a point in which indicates that the value of [tex]x[/tex] is [tex]3[/tex] and [tex]y[/tex] is [tex]4[/tex].
It is drawn by moving [tex]3[/tex] units right from the origin to positive [tex]x[/tex] axis and [tex]4[/tex] units upwards from the origin [tex](0,0)[/tex] to positive [tex]y[/tex]-axis.
A window air conditioner unit is placed on a laboratory bench and tested in cooling mode using 750 W of electric power with a COP of 1.75. What is the cooling power capacity and what is the net effect on the laboratory?
Answer:
Q=1312.5 W
Explanation:
Given that
Cooling load or power input = 750 W
COP=1.75
We know that COP can be given as
COP is the ratio of cooling effect to the input power .
Lets take cooling effect is Q.So now by using COP formula
COP=Q/750
1.75=Q/750
Q=1312.5 W
So the cooling effect produce by air conditioning will be 1312.5 W.
The net effect on laboratory,the laboratory temperature will reduce.
Air is compressed slowly in a piston-cylinder assembly from an initial state where P1 = 1.4 bar, V1= 4.25 m^3, to a final state where P2= 6.8 bar. During the process, the relation between pressure and volume follows pv= constant. For the air as the closed system, determine the work, in kJ
Answer:
W=-940.36 KJ
Explanation:
Given that
[tex]P_1=1\ bar,V_1=4.25 {m^3}[/tex]
[tex]P_2=6.8\ bar[/tex]
Process follows pv=constant
So this is the isothermal process and work in isothermal process given as
[tex]W=P_1V_1\ln \dfrac{P_1}{P_2}[/tex]
Now by putting the values (1.4 bar =140 KPa)
[tex]W=P_1V_1\ln \dfrac{P_1}{P_2}[/tex]
[tex]W=140\times 4.25 \ln \dfrac{1.4}{6.8}[/tex]
W=-940.36 KJ
Negative sign indicates that this is a compression process and work will given to the system.
Evaluate each of the following to three significant figures and express each answer in SI units using an appropriate prefix: (a) 354 mg (45 km) / (0.0356 kN), (b) (0.00453 Mg) (201 ms), and (c) 435 MN/23.2 mm.
The question requires calculating expressions using metric units and prefixes, converting them into SI units with appropriate prefixes, and ensuring these calculations are accurate to three significant figures.
Explanation:The question involves evaluating expressions with different units and converting them to SI units with appropriate prefixes, which requires a good understanding of metric prefixes and significant figures. Furthermore, examples of such conversions are provided to aid in this process.
Evaluations with SI Units and PrefixesFor part (a), you convert milligrams to kilograms, kilometers to meters, and kilonewtons to newtons, then perform the division ensuring that the answer is to three significant figures.For part (b), convert megagrams to kilograms and multiply by the given number of seconds, again reporting the answer to three significant figures.For part (c), convert meganewtons to newtons and millimeters to meters, divide, and round to three significant figures.Each conversion is an exercise in carefully applying metric prefixes and understanding how to manipulate them within calculations.
I have a 500 L tank that can hold a fluid. How much heavier or lighter will the tank be if a. The tank holds water at 80C compared to if the water tank holds 5C water? b. The tank holds air at 80C compared to if the water tank holds 5C air? Assume the tank is vented in a way that the pressure remains at atmospheric pressure, given as 101.3 KPa.
Answer:
water=14.1 kg
air=0.1348kg
Explanation:
Through laboratory tests, thermodynamic tables were developed, these allow to know all the thermodynamic properties of a substance (entropy, enthalpy, pressure, specific volume, internal energy etc ..)
through prior knowledge of two other properties such as pressure and temperature.
To solve this exercise we must find the specific volume of water and air in the two states and then subtract them and multiply them by the volume of the tank to find the change in mass, the following equation is inferred
Δm=V(ρ2-ρ1)
Where V= tank volume=500L=0.5m^3
ρ2= density of fluid in state 2
ρ1=density of fluid in state 1
Δm=change of mass
for water
ρ1=971.8kg/m^3(80C)
ρ2=1000kg/m^3(5C)
Δm=0.5(1000-971.8)
Δm=14.1 kg
for air
ρ1=0.9994kg/m^3(80C)
ρ2=1.269kg/m^3(5C)
Δm=0.5(1.269-0.9994)
Δm=0.1348kg
Solar energy is the most widely available renewable energy source and it is sufficient to meet entire needs of the world. However, it is not used extensively. Why?
Answer:
Explanation:
Solar energy is one of the Renewable sources of energy and it is sufficient to meet the entire needs of the world.
But it is not used extensively because of the inconsistency. Inconsistency means that sun rays are not consistent throughout the year. If the weather is not good or in winters earth does not receive sun rays continuously.
And another reason to not to set up solar energy is that it is very expensive not everyone can afford it.
The two basic network administration models are ____ and ____
The two basic network administration models are centralized and decentralized, each with distinct advantages and challenges that affect network performance, security, and scalability.
Explanation:The two basic network administration models are centralized and decentralized. In a centralized model, network control and decision-making are located at a single point, typically within a dedicated device or group of servers. Conversely, a decentralized model distributes control across multiple nodes, allowing for individual nodes to operate independently while still being part of the overall network.
Understanding these models is crucial for designing efficient networks that cater to specific organizational needs and for implementing dynamics on network models, such as discrete state/time models or continuous state/time models. Each model presents different advantages and challenges that can influence network performance, security, and scalability.
an aluminum bar 125mm (5in) long and having a square cross section 16.5mm (.65in) on an edge is pulled in tension with a load of 66,700 N (15000lb) and experiences an elongation of .43mm (1.7*10^-2 in ). assuming that the deformation is entirely elastic, calculate the modulus of elasticity of the aluminum.
The modulus of elasticity for the aluminum bar is calculated using the relationship between stress and strain, given by Young's modulus formula. The given values are substituted in the formula to find that the modulus of elasticity for the aluminum is approximately 60 GPa.
Explanation:Calculating the Modulus of Elasticity for Aluminum
To calculate the modulus of elasticity (also known as Young's modulus) for the aluminum bar, we can use the relationship described by Hooke's Law for elastic deformation, where stress is directly proportional to strain. The formula to find Young's modulus (Y) is:
Y = (F \/ A) \/ (\u0394L \/ L0)
Here, F is the force applied, A is the cross-sectional area, \u0394L is the change in length, and L0 is the original length of the bar.
Using the given values:
Force (F) = 66,700 NCross-sectional area (A) = 16.5 mm x 16.5 mm = 272.25 mm2 (or 272.25 x 10-6 m2)Change in length (\u0394L) = 0.43 mm (or 0.43 x 10-3 m)Original length (L0) = 125 mm (or 0.125 m)The calculation is as follows:
Y = (66,700 N / 272.25 x 10-6 m2) / (0.43 x 10-3 m / 0.125 m)
When the calculations are done, we find that the modulus of elasticity for the aluminum bar is approximately 60 GPa (Gigapascals), which is within the typical range for aluminum.
Calculate the modulus of elasticity of aluminum given specific values for force, length, cross-sectional area, and elongation during tension.
Young's modulus is a measure of a material's stiffness and is calculated using the formula: Y = (F * Lo) / (A * AL). Substituting the given values, we can find the modulus of elasticity of aluminum to be approximately 68 GPa.
What is the pressure inside a tire in (N/mm^2) if a pressure gauge indicates 29.35 psi?
Answer:
The pressure inside the tire is [tex]0.304\frac{N}{mm^{2}}[/tex]
Explanation:
The pressure gauge indicates the difference between the atmospheric pressure and the pressure inside the tire, so we have the following equation:
Pressure inside the tire = Gauge pressure + Atmospheric pressure
Where the gauge pressure is given in the problem and is 29.35psi and the atmospheric pressure is 14.7psi.
Replacing the values, we have:
Pressure inside the tire = 29.35psi + 14.7psi
Pressure inside the tire = 44.05psi
Now we have to convert from psi to [tex]\frac{N}{mm^{2}}[/tex], so:
44.05psi = [tex]44.05\frac{lbf}{in^{2}}[/tex]
[tex]44.05\frac{lbf}{in^{2}}*(\frac{1in}{25.4mm})^{2}*\frac{4.4482N}{lbf}=0.304\frac{N}{mm^{2}}[/tex]
What is meant by the thickness to chord ratio of an aerofoil?
Answer:
Chord ratio:
It is the ratio of thickness to the chord.It is also knows as thickness ratio.
Chord ratio measure the performance of wing when it is operating at the transonic speed.
When the speed cross the speed of sound wave then that wave creates the shock wave and these shock leads to produce drag force on the aerofoil profile.When Mach number is one then it means that if Mach increase then it will leads increase then drag force.
A storage tank, used in a fermentation process, is to be rotationally molded from polyethylene plastic. This tank will have a conical section at the bottom, right circular cylindrical mid-section and a hemispherical dome to cover the top. The radius of the tank is 1.5 m, the cylindrical side-walls will be 4.0 m in height, and the apex of the conic section at the bottom has an included angle of 60°. If the tank is filled to the top of the cylindrical side-walls, what is the tank capacity in liters?
Answer:
The volume up to cylindrical portion is approx 32355 liters.
Explanation:
The tank is shown in the attached figure below
The volume of the whole tank is is sum of the following volumes
1) Hemisphere top
Volume of hemispherical top of radius 'r' is
[tex]V_{hem}=\frac{2}{3}\pi r^3[/tex]
2) Cylindrical Middle section
Volume of cylindrical middle portion of radius 'r' and height 'h'
[tex]V_{cyl}=\pi r^2\cdot h[/tex]
3) Conical bottom
Volume of conical bottom of radius'r' and angle [tex]\theta [/tex] is
[tex]V_{cone}=\frac{1}{3}\pi r^3\times \frac{1}{tan(\frac{\theta }{2})}[/tex]
Applying the given values we obtain the volume of the container up to cylinder is
[tex]V=\pi 1.5^2\times 4.0+\frac{1}{3}\times \frac{\pi 1.5^{3}}{tan30}=32.355m^{3}[/tex]
Hence the capacity in liters is [tex]V=32.355\times 1000=32355Liters[/tex]
A galvanometer has a coil with a resistance of 24.0 Ω, and a current of 180 μA causes it to deflect full scale. If this galvanometer is to be used to construct an ammeter that can read up to 10.0 A, what shunt resistor is required? A galvanometer has a coil with a resistance of 24.0 , and a current of 180 μA causes it to deflect full scale. If this galvanometer is to be used to construct an ammeter that can read up to 10.0 A, what shunt resistor is required? 234 µΩ 123 µΩ 342 µΩ 423 µΩ 432 µΩ
Answer:
shunt resistor is 432µΩ
correct option is 432µΩ
Explanation:
given data
resistance R = 24.0 Ω
full scale deflection current Ig = 180 μA
galvanometer current I = 10.0 A
to find out
what shunt resistor is required
solution
we will apply here full scale deflection current formula that is
Ig = I × [tex]\frac{r}{r + R}[/tex] ...............1
here r is shunt current and R is resistance and I is galvanometer
put here all value
180 × [tex]10^{-6}[/tex] = 10 × [tex]\frac{r}{r + 24}[/tex]
r = 18 × [tex]10^{-6}[/tex] × 24
r = 432 × [tex]10^{-6}[/tex] Ω
so shunt resistor is 432µΩ
correct option is 432µΩ
Shunt resistor required for 10.0 A ammeter: approximately 432 μΩ.
To construct an ammeter using a galvanometer, a shunt resistor is connected in parallel to the galvanometer. The shunt resistor diverts most of the current, allowing only a fraction of the current to pass through the galvanometer, thus enabling it to measure higher currents.
The relationship between the current passing through the galvanometer and the shunt resistor can be expressed using the formula:
[tex]\[I_{\text{total}} = I_{\text{g}} + I_{\text{s}}\][/tex]
Where:
[tex]- \(I_{\text{total}}\)[/tex] is the total current (10.0 A)
[tex]- \(I_{\text{g}}\)[/tex] is the current passing through the galvanometer (180 μA)
[tex]- \(I_{\text{s}}\)[/tex] is the current passing through the shunt resistor
Given that the galvanometer resistance [tex]\(R_{\text{g}} = 24.0 Ω\)[/tex] and full-scale deflection current \[tex](I_{\text{g}} = 180 μA\),[/tex] we can calculate the shunt resistance required using Ohm's Law:
[tex]\[I_{\text{g}} = \frac{V_{\text{g}}}{R_{\text{g}}}\][/tex]
Where:
- [tex]\(V_{\text{g}}\)[/tex] is the voltage across the galvanometer
Since the galvanometer is designed to deflect full-scale at 180 μA, the voltage across it is:
[tex]\[V_{\text{g}} = I_{\text{g}} \times R_{\text{g}}\]\[V_{\text{g}} = (180 \times 10^{-6}) \times 24\]\[V_{\text{g}} = 0.00432 \, \text{V}\][/tex]
The current passing through the shunt resistor can be calculated using:
[tex]\[I_{\text{s}} = \frac{V_{\text{total}}}{R_{\text{s}}}\][/tex]
Since the total current is 10.0 A and the voltage across the shunt resistor is the same as the voltage across the galvanometer (as they are in parallel), we have:
[tex]\[I_{\text{s}} = \frac{10.0}{R_{\text{s}}}\][/tex]
Now, the total current equals the sum of the currents through the galvanometer and shunt resistor:
[tex]\[10.0 = 180 \times 10^{-6} + \frac{0.00432}{R_{\text{s}}}\][/tex]
Solving for [tex]\(R_{\text{s}}\):[/tex]
[tex]\[R_{\text{s}} = \frac{0.00432}{10.0 - 180 \times 10^{-6}}\]\[R_{\text{s}} ≈ \frac{0.00432}{10.0}\]\[R_{\text{s}} ≈ 432 \, \text{μΩ}\][/tex]
So, the required shunt resistor is approximately 432 μΩ. Therefore, the closest answer is 432 μΩ.
The "Crawler" developed to transport the Saturn V launch vehicle from the assembly building to the launch pad is the largest land 6 vehicle ever built, weighing 4.9 x 10 -Ibs at sea level. a- What is its mass in slugs ? b- What is its mass in kilograms ?
Answer:
a) 152000 slugs
b) 2220000 kg or 2220 metric tons
Explanation:
A body with a weight of 4.9*10^6 lbf has a mass of
4.9*10^6 lbm * 1 lbf/lbm = 4.9*10^6 lbm
This mass value can then be converted to other mass values.
1 slug is 32.17 lbm
Therefore:
4.9*10^6 lbm * 1 slug / (32.17 lbm) = 152000 slugs
1 lb is 0.453 kg
Therefore:
4.9*10^6 lbm / (1/0.453) * kg/lbm = 2220000 kg