Given:
applied tensile stress, [tex]\sigma[/tex] = 170 MPa
radius of curvature of crack tip, [tex]r_{t}[/tex] = [tex]3.5\times 10^{-4}[/tex] mm
crack length = [tex]4.5\times 10^{-2}[/tex] mm
half of internal crack length, a = [tex]\frac{crack length}{2} = \frac{4.5\times 10^{-2}}{2}[/tex]
a = [tex]2.25\times 10^{-2}[/tex]
Formula Used:
[tex]\sigma _{max} = 2\times\sigma \sqrt{\frac{a}{r_t}}[/tex]
Solution:
Using the given formula:
[tex]\sigma _{max} = 2\times170 \sqrt{\frac{2.25\times 10 ^{-2}}{3.5\times 10^{-4}}}[/tex]
[tex]\sigma _{max}[/tex] = 2726 MPa (395372.9 psi)
The magnitude of the maximum stress at the tip of an internal crack can be determined using the stress concentration factor formula.
Explanation:The magnitude of the maximum stress at the tip of an internal crack can be determined using the formula for the stress concentration factor, which is the ratio of the maximum stress to the applied stress. The stress concentration factor (Kt) for an internal crack can be calculated using the following equation:
Where Kt is the stress concentration factor, a is the crack length, and r is the radius of curvature of the crack.
Plugging in the given values:
Kt = 1 + 2 * (4.5 x 10-2 mm) / (3.5 x 10-4 mm) = 127
The magnitude of the maximum stress can be calculated by multiplying the stress concentration factor by the applied stress:
Maximum Stress = 127 * 170 MPa = 21,590 MPa
An aquarium 3 m long, 2 m wide, and 1 m deep is full of water. Find the work needed to pump half of the water out of the aquarium. (Use the fact that the density of water is 1000 kg/m3, and use 9.8 m/s2 for g.)
To find the work needed to pump half of the water out of the aquarium, you need to calculate the volume of the aquarium and the mass of the water. The work done is equal to the force (weight of the water) multiplied by the distance (height of the aquarium). Therefore, the work needed is 29400 Nm or J (Joules).
Explanation:To find the work needed to pump half of the water out of the aquarium, we first need to calculate the volume of the aquarium. The volume is given by length x width x height, which equals 3m x 2m x 1m = 6m³. Half of the water in the aquarium would be 6m³/2 = 3m³.
The density of water is given as 1000 kg/m³. So the mass of the water that needs to be pumped out is 3m³ x 1000 kg/m³ = 3000 kg.
The work done to pump the water out is given by the formula work = force x distance. In this case, the force required is the weight of the water, which is mass x gravity. The distance is the height of the aquarium, which is 1m.
Therefore, the work needed to pump half of the water out of the aquarium is 3000 kg x 9.8 m/s² x 1m = 29400 Nm or J (Joules).
Learn more about Work needed to pump water out of an aquarium here:https://brainly.com/question/28529285
#SPJ3
What is a gravational lens?
Final answer:
A gravitational lens occurs when a massive object like a galaxy causes the light from a more distant object to bend and magnify, much like how an optical lens works. Einstein predicted this based on general relativity, and its discovery has provided critical verification of this theory. The first gravitational lens was found in 1979, showing double images of a distant quasar.
Explanation:
A gravitational lens is a phenomenon where the light from a distant object, such as a quasar or galaxy, is bent and magnified by the gravity of a massive object, like a galaxy or galaxy cluster, that lies between the observer and the distant object. This effect is analogous to the way a conventional lens, like those found in glasses, bends light. Albert Einstein predicted this effect based on his theory of general relativity but thought it would be very unlikely for us to observe it. However, astronomers have since observed numerous instances of gravitational lensing, which provide significant evidence for general relativity. These observations include multiple images, arcs, or even rings of the same astronomical object, as gravity distorts the space around the massive intervening object.
The first gravitational lens was discovered in 1979 and presented dual images of the same distant object. This discovery and subsequent observations using powerful telescopes like the Hubble Space Telescope have allowed astronomers to study the universe's most distant objects and the distribution of dark matter. The bend of light due to massive objects can create spectacular effects such as Einstein rings, where a perfect alignment between the observer, massive object, and distant source results in a ring-like structure of light.
A metallic sheet has a large number of slits, 5.0 mm wide and 20 cm apart, and is used as a diffraction grating for microwaves. A wide parallel beam of microwaves is incident normally on the sheet. What is the smallest microwave frequency for which only the central maximum occurs? (c = 3.00 × 108 m/s)
Answer:
The smallest microwave frequency is 1.5 GHz.
Explanation:
Given that,
Distance d= 20 cm
We need to calculate the wavelength
Using formula for maximum diffraction
[tex]d\sin\theta=\lambda[/tex]
For maximum, [tex]\sin\thea=1[/tex]
[tex]d=\lambda[/tex]
[tex]\lambda=20 cm=0.2 m[/tex]
We need to calculate the frequency
[tex]f =\dfrac{c}{\lambda}[/tex]
[tex]f=\dfrac{3\times10^{8}}{0.2}[/tex]
[tex]f=1.5\times10^{9}\ Hz[/tex]
[tex]f=1.5 GHz[/tex]
Hence, The smallest microwave frequency is 1.5 GHz.
A marble rolls off a tabletop 1.0 m high and hits the floor at a point 1.2 m away from the table’s edge in the horizontal direction. What is the speed of the marble when it leaves the table’s edge?
A. 1.2 m/s
B. 9.8 m/s
C. 2.7 m/s
D. 3.7 m/s
Answer:
C. 2.7 m/s
Explanation:
Consider the motion of the marble along the vertical direction
y = vertical displacement = height of tabletop = 1.0 m
a = acceleration = 9.8 m/s²
t = time taken to hit the floor = ?
v₀ = initial speed of the marble along vertical direction = 0 m/s
Using the equation
y = v₀ t + (0.5) a t²
1.0 = (0) t + (0.5) (9.8) t²
t = 0.45 s
Consider the motion of the marble along the horizontal direction :
v = speed with which the marble leaves the table
x = horizontal displacement = 1.2 m
t = 0.45 s
horizontal displacement is given as
x = v t
1.2 = v (0.45)
v = 2.7 m/s
Three particles are fixed on an x axis. Particle 1 of charge q1 is at x = a, and particle 2 of charge q2 is at x = - a. If their net electrostatic force on particle 3 of charge + Q is to be zero, what must be the ratio q2/q1 when particle 3 is at x = 0.500a?
Answer:
9
Explanation:
As the net force on Q is zero, so the force on Q due to q1 is balanced by the force on Q due to q2.
Let the force on Q due to q1 is F1 and force on Q due to q2 is F2.
F1 = F2
K Q q1 / (0.5 a)^2 = K Q q2 / (1.5 a)^2
q1 / 0.25 = q2 / 2.25
q2 / q1 = 2.25 / 0.25
q2 / q1 = 9
_________is defined as the how many cycles are completed in one second by an oscillating object. Frequency Period Linear Velocity Momentum
Answer:
Frequency
Explanation:
The number of cycles completed in one second by an oscillating object is called its frequency. The term frequency shows number of times an oscillation is occurring. It is denoted by [tex]\nu[/tex]. The reciprocal of frequency is called the time period of the wave i.e.
[tex]\nu=\dfrac{1}{T}[/tex]
T = time period
So, the correct option is (a) "frequency".
Final answer:
Frequency is the number of oscillations per second, measured in hertz (Hz), and is inversely related to the period (T), which is the time it takes to complete one oscillation.
Explanation:
Frequency is defined as the number of cycles completed in one second by an oscillating object. In physics, frequency (f) is the number of oscillations that take place per unit of time. The SI unit for frequency is the hertz (Hz), which is equivalent to one oscillation per second. The relationship between frequency and period (T) is given by f = 1/T, meaning that as the period increases, the frequency decreases, and vice versa.
Periodic motion, such as that of a mass suspended by a wire undergoing simple harmonic motion, has a constant time to complete one cycle, known as the period (T). Its units are usually seconds. Period refers to the time it takes to complete one oscillation, while frequency is the number of these oscillations within a given timeframe.
Using a rope that will snap if the tension in it exceeds 356 N, you need to lower a bundle of old roofing material weighing 478 N from a point 7.50 m above the ground. (a) What magnitude of the bundle's acceleration will put the rope on the verge of snapping? (b) At that acceleration, with what speed would the bundle hit the ground?
Answer:
a) 2.5 m/s²
b) 6.12 m/s
Explanation:
Tension of rope = T = 356N
Weight of material = W = 478 N
Distance from the ground = s = 7.5 m
Acceleration due to gravity = g = 9.81 m/s²
Mass of material = m = 478/9.81 = 48.72
Final velocity before the bundle hits the ground = v
Initial velocity = u = 0
Acceleration experienced by the material when being lowered = a
a) W-T = ma
⇒478-356 = 48.72×a
[tex]\Rightarrow \frac{122}{48.72} = a[/tex]
⇒a = 2.5 m/s²
∴ Acceleration achieved by the material is 2.5 m/s²
b) v²-u² = 2as
⇒v²-0 = 2×2.5×7.5
⇒v² = 37.5
⇒v = 6.12 m/s
∴ Velocity of the material before hitting the ground is 6.12 m/s
Aluminum has a magnetic susceptibility χ = 1.7 × 10-5 at T = 300 K. What will be the magnetization of a small sample of aluminum placed in a 1.5 T magnetic field at T = 150 K?
Answer:
The magnetization of a small sample of aluminum is 40.6 A/m
Explanation:
Given that,
Magnetic susceptibility [tex]\chi_{1}=1.7\times10^{-5}[/tex] at 300 K
Magnetic field = 1.5 T
We need to calculate the magnetic susceptibility at 150 K
[tex]\dfrac{\chi_{2}}{\chi_{1}}=\dfrac{T_{1}}{T_{2}}[/tex]
Put the value into the formula
[tex]\dfrac{\chi_{2}}{1.7\times10^{-5}}=\dfrac{300}{150}[/tex]
[tex]\chi_{2}=\dfrac{300\times1.7\times10^{-5}}{150}[/tex]
[tex]\chi_{2}=3.4\times10^{-5}[/tex]
We need to calculate the magnetization
Using formula of magnetization
[tex]I=\chi_{2}\times H[/tex]
Where, H = magnetic intensity
Formula of magnetic intensity
[tex]H=\dfrac{B}{\mu_{0}}[/tex]
Where, B = magnetic field
Put the value of H into the formula of magnetization
[tex]I=\chi_{2}\times\dfrac{B}{\mu_{0}}[/tex]
[tex]I=3.4\times10^{-5}\times\dfrac{1.5}{4\pi\times10^{-7}}[/tex]
[tex]I=40.6\ A/m[/tex]
Hence, The magnetization of a small sample of aluminum is 40.6 A/m
In a performance test, each of two cars takes 9.0 s to accelerate from rest to 28 m/s. Car A has a mass of 1379 kg, and car B has a mass of 1902 kg. Find the net average force that acts on (a) car A and (b) car B during the test.
Explanation:
It is given that,
Mass of car A, [tex]m_A=1379\ kg[/tex]
Mass of car B, [tex]m_B=1902\ kg[/tex]
In a performance test, each of two cars takes 9.0 s to accelerate from rest to 28 m/s. Their acceleration is given by :
[tex]a=\dfrac{v-u}{t}[/tex]
[tex]a=\dfrac{28\ m/s}{9}[/tex]
a = 3.12 m/s²
(a) The net force of car A, [tex]F_A=m_Aa[/tex]
[tex]F_A=1379\ kg\times 3.12\ m/s^2[/tex]
[tex]F_A=4302.48\ N[/tex]
(b) The net force of car B, [tex]F_B=m_Ba[/tex]
[tex]F_B=1902\ kg\times 3.12\ m/s^2[/tex]
[tex]F_A=5934.24\ N[/tex]
Hence, this is the required solution.
What is the wavelength of an ultrasound signal having a velocity of 1,500 m/sec. at 2.5 MHz?
Answer:
The wavelenght is λ= 6 * 10⁻⁴m.
Explanation:
v= 1500 m/s
f= 2.5 MHz = 2.5 *10⁶ Hz
λ=v/f
λ= 6 * 10⁻⁴ meters
A football player with a mass of 88 kg and a speed of 2.0 m/s collides head-on with a player from the opposing team whose mass is 120 kg. The players stick together and are at rest after the collision. Find the speed of the second player, assuming the speed of light is 3.0 m/s.
Answer:
Speed of another player, v₂ = 1.47 m/s
Explanation:
It is given that,
Mass of football player, m₁ = 88 kg
Speed of player, v₁ = 2 m/s
Mass of player of opposing team, m₂ = 120 kg
The players stick together and are at rest after the collision. It shows an example of inelastic collision. Using the conservation of linear momentum as :
[tex]m_1v_1+m_2v_2=(m_1+m_2)V[/tex]
V is the final velocity after collision. Here, V = 0 as both players comes to rest after collision.
[tex]v_2=-\dfrac{m_1v_1}{m_2}[/tex]
[tex]v_2=-\dfrac{88\ kg\times 2\ m/s}{120\ kg}[/tex]
[tex]v_2=-1.47\ m/s[/tex]
So, the speed of another player is 1.47 m/s. Hence, this is the required solution.
g A box having mass 0,5kg is placed in front of a 20 cm compressed spring. When the spring released, box having mass m1, collide box having mass m2 and they move together. Find the velocity of boxes.
Answer:Expression given below
Explanation:
Given mass of spring[tex]\left ( m_1\right )=0.5 kg[/tex]
Compression in the spring[tex]\left ( x\right )=20 cm[/tex]
Let the spring constant be K
Using Energy conservation
potential energy stored in spring =Kinetic energy of Block[tex]\left ( m_1\right )[/tex]
[tex]\frac{1}{2}Kx^2=\frac{1}{2}m_1v^2[/tex]
[tex]v=x\sqrt{\frac{k}{m_1}}[/tex]
now conserving momentum
[tex]m_1v=\left ( m_1+m_2\right )v_0[/tex]
[tex]v_0=\frac{m_1}{m_1+m_2}v[/tex]
where [tex]v_0[/tex] is the final velocity
An EM wave has a wavelength A 500 nm and a peak electric field Eo 100 i. The wave propagates along the z axis. a) What is the magnitude and direction of the magnetic field? b) What is the frequency f? c) What is the angular frequency w? d) What is the wavenmber k?
Answer:
(a) 3.33 x 10^-7 T along Y axis
(b) 6 x 10^14 Hz
(c) 3.768 x 10^15 rad/s
(d) 2 x 10^6 m^-1
Explanation:
Wavelength = 500 nm = 500 x 10^-9 m
Electric Field, E = 100 i (along + X axis)
Wave is in +Z axis
So, the magnetic field is in + Y axis.
(a) c = E / B
B = E / c = 100 / (3 x 10^8) = 3.33 x 10^-7 T along Y axis
(b) Frequency = wave speed / wavelength = ( 3 x 10^8) / (500 x 10^-9)
frequency = 6 x 10^14 Hz
(c) w = 2 x 3.14 x f = 2 x 3.14 x 6 x 10^14 = 3.768 x 10^15 rad/s
(d) k = reciprocal of wavelength = 1 / (500 x 10^-9) = 2 x 10^6 m^-1
The car has a mass of 1.6 Mg and center of mass at G. If the coefficient of static friction between the shoulder of the road and the tires is μs = 0.41, determine the greatest slope θ the shoulder can have without causing the car to slip or tip over if the car travels along the shoulder at constant velocity.
The greatest slope the shoulder can have without causing the car to slip or tip over is 22.3⁰.
The given parameters;
mass of the car, m = 1.6 Mgcoefficient of static friction, [tex]\mu_ s[/tex] = 0.41The greatest slope of the shoulder is determined by taking net force on the car as shown below;
[tex]\Sigma F= ma \\\\Wsin\theta - \mu_s Wcos \theta = ma[/tex]
at constant velocity, acceleration, a, = 0
[tex]Wsin\theta - \mu_s W cos \theta = 0\\\\W sin\theta = \mu_s Wcos \theta \\\\\mu_s = \frac{Wsin\theta }{W cos \theta } \\\\\mu_s = tan \theta \\\\\theta = tan^{-1}(\mu_s)\\\\\theta = tan^{-1}(0.41)\\\\\theta =22.3\ ^0[/tex]
Thus, the greatest slope the shoulder can have without causing the car to slip or tip over is 22.3⁰.
Learn more here:https://brainly.com/question/14514652
The greatest slope the car can be without slipping or tipping over is approximately 22.4 degrees where weight due to gravity is balanced by static friction.
Explanation:This problem involves the concept of static friction, which prevents an object from sliding down a slope. Here, the car is held in place on a slope due to static friction between the tires and the road. First, we need to calculate the force of gravity acting on the car, which is the weight of the car mg. The mass of the car is given as 1.6 Mg = 1.6 x 10^6 grams. Therefore, the weight of the car is 1.6 x 10^6 g * 9.8 m/s² = 1.568 x 10^7 N.
Next, the force of static friction is given by the equation μsN, where N is the normal force and μs is the coefficient of static friction which is 0.41. Since the car is not moving, the net force on it must be zero. This implies that the force of static friction must balance out the force of gravity. So, we equate the forces and solve for the slope angle θ, getting a relationship: tan θ = μs.
So, θ = tan^-1 (0.41) ≈ 22.4°. Therefore, the greatest slope the shoulder can have without causing the car to slip or tip over is approximately 22.4 degrees.
Learn more about Static Friction here:https://brainly.com/question/13000653
#SPJ11
An object essentially at infinity is moved to a distance of 90 cm in front of a thin positive lens. In the process its image distance triples. Determine the focal length of the lens.
Answer:
67.5 cm
Explanation:
u = - 90 cm, v = 3 x u = 3 x 90 = 270 cm
let f be the focal length
Use lens equation
1 / f = 1 / v - 1 / u
1 / f = 1 / 270 + 1 / 90
1 / f = 4 / 270
f = 67.5 cm
To determine the focal length of the lens, we use the lens formula and set up an equation based on the given information. Solving for the image distance, we find that it is zero, indicating the image is formed at infinity. Therefore, the focal length of the lens is 90 cm.
Explanation:To determine the focal length of the lens, we can use the lens formula:
1/f = 1/v - 1/u
Where f is the focal length, v is the image distance, and u is the object distance.
Given that the image distance triples when the object is moved from infinity to 90 cm in front of the lens, we can set up the following equation:
1/f = 1/(3v) - 1/(90)
Multiplying through by 90*3v, we get:
90*3v/f = 270v - 90*3v
90*3v/f = 270v - 270v
90*3v/f = 0
Simplifying further, we find that: v = 0
When the image distance is zero, it means the image is formed at infinity, so the lens is focused at the focal point. Therefore, the focal length of the lens is 90 cm.
You push downward on a box at an angle 25° below the horizontal with a force of 750 N. If the box is on a flat horizontal surface for which the coefficient of static friction with the box is 0.66, what is the mass of the heaviest box you will be able to move?
Answer:
72.75 kg
Explanation:
[tex]F[/tex] = force applied on a box = 750 N
[tex]m[/tex] = mass of the box
[tex]N[/tex] = Normal force on the box
[tex]\mu _{s}[/tex] = Coefficient of static friction = 0.66
From the force diagram, force equation along the vertical direction is given as
[tex]N = F Sin25 + mg[/tex]
[tex]N = 750 Sin25 + mg[/tex] eq-1
Static frictional force is given as
[tex]f_{s} = \mu _{s} N[/tex]
using eq-1
[tex]f_{s} = \mu _{s} (750 Sin25 + mg)[/tex]
For the box to move,
[tex]F Cos25 = f_{s}[/tex]
[tex]750 Cos25 = \mu _{s} (750 Sin25 + mg)[/tex]
[tex]750 Cos25 = (0.66) (750 Sin25 + m (9.8))[/tex]
m = 72.75 kg
A bathroom scale is compressed 0.21 in. when a 210-lb person stands on it. Assuming that the scale behaves like a spring that obeys Hooke's law, how much does someone who compresses the scale 0.06 in. weigh? How much work is done compressing the scale 0.06 in.?
Bathroom scales measure weight by compressing springs in proportion to the applied force. Using Hooke's law, the spring constant can be determined to calculate the weight. If the scale is compressed by 0.21 inches, a 210-lb person is standing on it. When compressed by 0.06 inches, the weight is calculated to be 60 lb. The work done in compressing the scale by 0.06 inches is 3.6 lb-in or 0.3 ft-lb.
Explanation:Bathroom scales measure weight. When you stand on a bathroom scale, it compresses slightly due to the weight placed on it. The scale contains springs that compress in proportion to the weight, similar to how rubber bands expand when pulled. Using Hooke's law, we can calculate the weight of someone based on how much the scale is compressed.
If a 210-lb person compresses the scale by 0.21 inches, and assuming the scale behaves like a spring, we can use Hooke's law (F = kx) to find the spring constant. The spring constant is the amount of force required to compress the spring by a certain distance. Rearranging the equation for Hooke's law, we get k = F/x. Plugging in the values, k = 210 lb / 0.21 in = 1000 lb/in.
To find the weight of someone who compresses the scale by 0.06 inches, we can again use Hooke's law. Rearranging the equation to solve for F, we have F = kx. Plugging in the values, F = 1000 lb/in * 0.06 in = 60 lb.
To calculate the work done in compressing the scale by 0.06 inches, we can use the formula for work: W = Fd, where W is work, F is force, and d is distance. Plugging in the values, W = 60 lb * 0.06 in = 3.6 lb-in or 0.3 ft-lb.
A potter's wheel of radius 11 cm starts from rest and rotates with constant angular accel- eration until at the end of 35 s it is moving with angular velocity of 19 rad/s. What is the angular acceleration? Answer in units of rad/s2.
Final answer:
The angular acceleration of the potter's wheel is approximately 0.543 rad/s^2, calculated by dividing the final angular velocity by the time taken to reach it.
Explanation:
To calculate the angular acceleration of a potter's wheel that starts from rest and reaches an angular velocity of 19 rad/s in 35 seconds, we can use the following kinematic equation for rotational motion:
\(\omega = \omega_0 + \alpha \times t\)
Where:
\(\omega\) is the final angular velocity.
\(\omega_0\) is the initial angular velocity (0 rad/s since the wheel starts from rest).
\(\alpha\) is the angular acceleration.
\(t\) is the time taken to reach the final angular velocity.
Substituting the given values:
19 rad/s = 0 rad/s + \(\alpha\) \times 35 s
To solve for \(\alpha\), we rearrange the equation:
\(\alpha = \frac{19 rad/s}{35 s}\)
\(\alpha = \frac{19}{35} rad/s^2\)
\(\alpha \approx 0.543 rad/s^2\)
Therefore, the angular acceleration of the potter's wheel is approximately 0.543 rad/s2.
A football player pushes a sled on a level surface with a weight force of 760 N that acts perpendicular to the surface. The coefficient of kinetic friction between the sled and grass is 0.78 How much work does the football player perform if he pushes the sled and displaces it 10 m. Assume ) the average force performed is equal to the force required to keep the sled in motion and 2) the applied force is paraîlel to the sleds displacement. (3 points) a. b. How much power did the football player produce if he performed the sled push in 3.21 seconds? (2 point)
Answer:
Part a)
W = 5928 J
Part b)
P = 592.8 Watt
Explanation:
As we know that force of friction on the sled is given by
[tex]F_f = \mu F_n[/tex]
here we know that
[tex]\mu = 0.78[/tex]
also we know that normal force on the sled is counter balanced by the weight of the object
[tex]F_n = mg = 760 N[/tex]
now we have
[tex]F_f = (0.78)(760) = 592.8 N[/tex]
Now the applied force must be equal to this friction force so that it will start sliding on the grass
now if we push it by 10 m distance then work done to slide it given by
[tex]W = F.d[/tex]
[tex]W = (592.8)(10) = 5928 J[/tex]
Part B)
Power required to push the sled in 10 s
[tex]Power = \frac{work}{time}[/tex]
[tex]Power = \frac{5928}{10} = 592.8 Watt[/tex]
A 920-kg car with brakes applied travels at constant speed a distance of 8 m downhill along a road that makes an angle of 30o below the horizontal. The work W done by the force of gravity during this motion is:
Answer:
W = 36064 J
Explanation:
Work done by the force of gravity is given as
[tex]W_g = F_g \times d[/tex]
here we know that
[tex]F_g = mg[/tex]
also we have
[tex]d[/tex] = vertical displacement of the car in downward direction
now we have
[tex]d = 8 sin30[/tex]
[tex]d = 4 m[/tex]
now work done is given as
[tex]W = (mg) d[/tex]
[tex]W = (920 \times 9.81)(4)[/tex]
[tex]W = 36064 J[/tex]
A generator produces 60 A of current at 120 V. The voltage is usually stepped up to 4500 V by a transformer and transmitted through a power line of total resistance 1.0 Ω. Find the percentage power lost in the transmission line if the voltage is not stepped up.
Without stepping up the voltage, 50% of the power is lost in the transmission due to the high I^2R losses. Stepping up the voltage using a transformer significantly reduces these losses and makes power transmission more effective.
Explanation:The subject question pertains to the percentage power loss in a given transmission line when the voltage is not stepped up. Intuitively, power loss will be considerably greater when voltage is not stepped up due to a relatively high current flowing through the lines that enormously increases the I2R (current squared times the resistance) losses.
Firstly, calculate the initial power, PInitial using the formula P = IV, where I is current and V is voltage. In this case, PInitial = 60 A * 120 V = 7200 W. If the voltage is not stepped up, this power is transmitted at 120 V.
The power dissipated due to resistance (Ploss) can be calculated using the formula P = I2R, where I is current and R is resistance. So: Ploss = (60 A)2 * 1 Ω = 3600 W. The percentage of power loss is thus (Ploss / PInitial) * 100 = (3600 W / 7200 W) * 100 = 50%.
In contrast, when voltage is stepped up to 4500 V using a transformer, the current decreases to maintain the same power, greatly reducing power losses. This is eminently beneficial over long distances, making power transmission more efficient.
Learn more about Power Loss in Transmission Lines here:https://brainly.com/question/37778137
#SPJ12
Final answer:
the percentage power lost in the transmission line if the voltage is not stepped up is 50%
Explanation:
To calculate the percentage power lost in the transmission line if the voltage is not stepped up, we first calculate the power loss in the transmission line using the formula P = I²R, where I is the current and R is the resistance of the transmission line.
We are given that the current I is 60 A and the total resistance R is 1.0 Ω. The power loss in the transmission line would be:
P = (60 A)² × 1.0 Ω = 3600 W or 3.6 kW
The total power transmitted without stepping up the voltage is calculated as P = IV, where V is the voltage. Here, V is 120 V, so the total power transmitted is:
P = 60 A × 120 V = 7200 W or 7.2 kW
To find the percentage power lost, we divide the power lost by the total power transmitted and multiply by 100:
Percentage power lost = (3600 W / 7200 W) × 100% = 50%
Without the step-up transformer, 50% of the power would be lost in the transmission line, which is a significant loss compared to transmission at a higher voltage. This example illustrates the importance of high-voltage transmission in reducing power losses.
A combination of 0.250 kg of water at 20.0°C, 0.400 kg of aluminum at 26.0°C, and 0.100 kg of copper at 100°C is mixed in an insulated container and allowed to come to thermal equilibrium. Ignore any energy transfer to or from the container and determine the final temperature of the mixture.
Answer:
23.63 °C
Explanation:
[tex]m_{w}[/tex] = mass of water = 0.250 kg
[tex]T_{wi}[/tex] = initial temperature of water = 20.0 °C
[tex]c_{w}[/tex] = Specific heat of water = 4186 J/(kg °C)
[tex]m_{a}[/tex] = mass of aluminum = 0.400 kg
[tex]T_{ai}[/tex] = initial temperature of aluminum = 26.0 °C
[tex]c_{a}[/tex] = Specific heat of aluminum = 900 J/(kg °C)
[tex]m_{c}[/tex] = mass of copper = 0.100 kg
[tex]T_{ci}[/tex] = initial temperature of copper = 100 °C
[tex]c_{c}[/tex] = Specific heat of copper = 386 J/(kg °C)
[tex]T_{f}[/tex] = Final temperature of mixture
Using conservation of heat
[tex]m_{w}[/tex] [tex]c_{w}[/tex] ([tex]T_{f}[/tex] - [tex]c_{w}[/tex]) + [tex]m_{a}[/tex] [tex]c_{a}[/tex] ([tex]T_{f}[/tex] - [tex]T_{ai}[/tex] ) + [tex]m_{c}[/tex] [tex]c_{c}[/tex] ([tex]T_{f}[/tex] - [tex]T_{ci}[/tex] ) = 0
(0.250) (4186) ([tex]T_{f}[/tex] - 20) + (0.400) (900) ([tex]T_{f}[/tex] - 26) + (0.100) (386) ([tex]T_{f}[/tex] - 100) = 0
[tex]T_{f}[/tex] = 23.63 °C
A flat circular coil having a diameter of 25 cm is to produce a magnetic field at its center of magnitude, 1.0 mT. If the coil has 100 turns how much current must pass through the coil?
Answer:
The current pass through the coil is 6.25 A
Explanation:
Given that,
Diameter = 25 cm
Magnetic field = 1.0 mT
Number of turns = 100
We need to calculate the current
Using the formula of magnetic field
[tex]B =\dfrac{\mu_{0}NI}{2\pi r}[/tex]
[tex]I=\dfrac{B\times2\pi r}{\mu N}[/tex]
Where, N = number of turns
r = radius
I = current
Put the value into the formula
[tex]I=\dfrac{1.0\times10^{-3}\times2\pi\times12.5\times10^{-2}}{4\pi\times10^{-7}100}[/tex]
[tex]I=6.25\ A[/tex]
Hence, The current passes through the coil is 6.25 A
When performing the pupillary reflexes, describe the position of the subject and environment
the subject should be comfortable and relaxed in a well lit area
the subject should be seated, relaxed in a dimly lit area with one eye closed
the subject should be seated, relaxed in a well lit area with one eye closed
the subject should be comfortable and relaxed in a dimly lit area, the subject should shield their eyes by placing their hand vertically between the eye and nose
Answer:
The pupillary light reflex (PLR) or photopupillary reflex is a reflex that controls the diameter of the pupil, in response to the intensity (luminance) of light that falls on the retinal ganglion cells of the retina in the back of the eye, thereby assisting in adaptation of vision to various levels of lightness/darkness.
A greater intensity of light causes the pupil to constrict (miosis/myosis; thereby allowing less light in), whereas a lower intensity of light causes the pupil to dilate (mydriasis, expansion; thereby allowing more light in)
Explanation:
A rocket takes off from Earth and reaches a speed of 105 m/s in 18.0 s. If the exhaust speed is 1,200 m/sand the mass of fuel burned is 110 kg, what was the initial mass (in kg, including the initial fuel) of the rocket?
Answer:
The initial mass of the rocket is 526.2 kg.
Explanation:
Given that,
Final speed = 105 m/s
Time = 18.0 s
Exhaust initial speed = 1200 m/s
Mass of burned fuel = 110 kg
We need to calculate the initial mass
The velocity change of rocket under gravity is defined as,
[tex]v=u\ ln(\dfrac{m_{i}}{m})-gt[/tex]....(I)
We know that,
[tex]m=m_{i}-m_{bf}[/tex]
Put the value of m in equation (I)
[tex]v=u\ ln(\dfrac{m_{i}}{m_{i}-m_{bf}})-gt[/tex]
[tex]m_{i}=\dfrac{m_{bf}}{1-e^-{\dfrac{v+gt}{u}}}[/tex]
[tex]m_{i}=\dfrac{110}{1- e^-{\frac{105+9.8\times18}{1200}}}[/tex]
[tex]m_{i}=526.2 kg[/tex]
Hence, The initial mass of the rocket is 526.2 kg.
The initial mass of the rocket including the initial fuel is 1257.14 kg.
Conservation of linear momentum
The initial mass of the rocket is determined by applying the principle of conservation of linear momentum as follows;
m₁v₁ = m₂v₂
105m = 1200 x 110
105 m = 132,000
m = 132,000/105
m = 1257.14 kg
Thus, the initial mass of the rocket including the initial fuel is 1257.14 kg.
Learn more about conservation of linear momentum here: https://brainly.com/question/7538238
At the equator, near the surface of the Earth, the magnetic field is approximately 50.0 µT northward, and the electric field is about 100 N/C downward in fair weather. Find the gravitational, electric, and magnetic forces on an electron in this environment, assuming the electron has an instantaneous velocity of 5.90 ✕ 106 m/s directed to the east in this environment.
Answer:
[tex]F_g = 8.9 \times 10^{-30} N[/tex]
[tex]F_e = 1.6 \times 10^{-17} N[/tex]
[tex]F_m = 4.72 \times 10^{-17} N[/tex]
Explanation:
For gravitational force we know that
F = mg
now we have
[tex]m = 9.1 \times 10^{-31} kg[/tex]
[tex]F_g = (9.1 \times 10^{-31})(9.8)[/tex]
[tex]F_g = 8.9 \times 10^{-30} N[/tex]
Now electrostatic force
[tex]F = qE[/tex]
here we have
[tex]F = (1.6 \times 10^{-19})(100)[/tex]
[tex]F = 1.6 \times 10^{-17} N[/tex]
Now magnetic force on it is given by
[tex]F_{m} = qvB[/tex]
[tex]F_m = (1.6 \times 10^{-19})(5.90 \times 10^6)(50 \times 10^{-6})[/tex]
[tex]F_m = 4.72 \times 10^{-17} N[/tex]
The gravitational force on the electron is 8.90 x 10^-31 N downward, the electric force on the electron is 1.60 x 10^-17 N upward, and the magnetic force on the electron is 5.90 x 10^-25 N northward.
Explanation:The gravitational force on an electron near the surface of the Earth can be calculated using the formula Fg = m * g, where m is the mass of the electron and g is the acceleration due to gravity. The electric force on the electron can be calculated using the formula Fe = q * E, where q is the charge of the electron and E is the magnitude of the electric field. The magnetic force on the electron can be calculated using the formula Fm = q * v * B, where v is the velocity of the electron and B is the magnitude of the magnetic field.
Given that the electron has a mass of 9.11 x 10^-31 kg, a charge of -1.60 x 10^-19 C, and a velocity of 5.90 x 10^6 m/s, the gravitational force on the electron is approximately 8.90 x 10^-31 N downward. The electric force on the electron is approximately 1.60 x 10^-17 N upward. The magnetic force on the electron is approximately 5.90 x 10^-25 N northward.
(I) What is the capacitance of a pair of circular plates with a radius of 5.0 cm separated by 3.2 mm of mica?
As per the details given, the capacitance of the pair of circular plates is approximately [tex]\(1.11 \times 10^{-11}\) Farads.[/tex]
A capacitor is a device made to store electric charge, and one of its basic electrical characteristics is capacitance.
When a voltage difference (potential difference) exists between a capacitor's two conducting plates, the capacity of the capacitor to store and hold electrical energy is measured.
Capacitance is a measurement of how much charge can be held on a capacitor's plates for a specific voltage.
The capacitance (C) of a parallel plate capacitor is given by the formula:
[tex]\[ C = \dfrac{\varepsilon_0 \cdot A}{d} \][/tex]
Where:
[tex]\( \varepsilon_0 \)[/tex] is the vacuum permittivity ([tex]\(8.85 \times 10^{-12} \, \text{F/m}\)[/tex])
A is the area of the plates (in square meters)
d is the distance between the plates (in meters)
Given:
Radius of the circular plates (r) = 5.0 cm
= 0.05 m
Distance between the plates (d) = 3.2 mm
= 0.0032 m
Calculate the area of one of the plates:
[tex]\[ A = \pi \cdot r^2 \\\\= \pi \cdot (0.05 \, \text{m})^2 \][/tex]
Calculate the capacitance (C):
[tex]\[ C = \dfrac{\varepsilon_0 \cdot A}{d} \\\\= \dfrac{8.85 \times 10^{-12} \, \text{F/m} \cdot \pi \cdot (0.05 \, \text{m})^2}{0.0032 \, \text{m}} \][/tex]
[tex]\[ C \approx 1.11 \times 10^{-11} \, \text{F} \][/tex]
Thus, the capacitance of the pair of circular plates is approximately [tex]\(1.11 \times 10^{-11}\)[/tex] Farads.
For more details regarding capacitance, visit:
https://brainly.com/question/31871398
#SPJ12
The capacitance of a pair of circular plates with a radius of 5.0 cm separated by 3.2 mm of mica is 10.3 pF. This is calculated using the formula for the capacitance of a parallel plate capacitor and the area of a circle.
Explanation:To determine the capacitance of a pair of circular plates of a parallel plate capacitor with a given radius, separated by a specific dielectric material, we use the formula:
C = ε0 εr (A/d)
Where:
C is the capacitance,
ε0 is the vacuum permittivity (8.85 × 10-12 F/m),
εr is the relative permittivity of the dielectric (for mica, it's approximately 6),
A is the area of one of the plates, and
d is the separation between the plates.
To find the area A of a circular plate with radius r, we use the formula A = πr2. For a radius of 5.0 cm (or 0.05 m), A = π(0.05 m)2 = 7.85 × 10-3 m2.
Substituting into the capacitance formula, with d = 3.2 mm (or 0.0032 m), we get:
C = (8.85 × 10-12 F/m) × 6 × (7.85 × 10-3 m2/0.0032 m) = 1.03 × 10-11 F
This result is usually expressed in picofarads (pF), so the capacitance is 10.3 pF.
An atomic nucleus with a rest mass energy of 7134 MeV is accelerated to 99.217% the speed of light relative to the lab frame. What is the Kinetic Energy in MeV of the atomic nucleus in the lab frame? Assume 4 significant figures.
Answer:
4.999 × 10⁴ MeV
Explanation:
Kinetic energy is related to the rest energy by the Lorentz transformation equation as shown below.
Kinetic energy in the lab frame K= ( γ -1 ) Eo
The Lorentz constant γ = [tex]1/\sqrt{1-v^2/c^2}[/tex]
So γ = [tex]1/\sqrt{1- (0.99217 c)^2/c^2}[/tex]= 8.0067
⇒ K = (8.0067-1)(7134) = 49986 MeV
=49,999 MeV ( 4 significant figures)
A current density of 7.00 10-13 A/m2 exists in the atmosphere at a location where the electric field is 185 V/m. Calculate the electrical conductivity of the Earth's atmosphere in this region.
Answer:
electrical conductivity is given as
[tex]\sigma = 3.8 \times 10^{-15} [/tex]
Explanation:
For a current carrying conductor we will have relation between current density and electric field inside the conductor as
[tex]j = \sigma E[/tex]
here we have
current density = j
electric field = E
given that
[tex]j = 7.00 \times 10^{-13}[/tex]
[tex]E = 185 V/m[/tex]
now we will have
[tex]\sigma = \frac{j}{E}[/tex]
[tex]\sigma = \frac{7.00 \times 10^{-13}}{185}[/tex]
[tex]\sigma = 3.8 \times 10^{-15} [/tex]
Water enters a 180° elbow with an average velocity V1 = 3 m/s. The diameter at the inlet of the elbow is 6.0 cm and the exit diameter is 2.0 cm. The water exits to atmosphere. Determine the magnitude of the horizontal force required to hold the elbow in place. (Ignore the pressure component of the force.)
Answer:203.60 N
Explanation:
Given
[tex]V_{inlet}[/tex]=3 m/s
[tex]d_{inlet}[/tex]=6 cm
[tex]d_{outlet}[/tex]=2 cm
Using continuity equation
[tex]A_{inlet}V_{inlet}=A_{outlet}V_{outlet}[/tex]
[tex]\frac{\pi \times d_{inlet}^2}{4}\times 3[/tex]=[tex]\frac{\pi \times d_{outlet}^2}{4}\times V_{outlet}[/tex]
[tex]V_{outlet}[/tex]=27 m/s
Horizontal Force required to hold elbow=Change in momentum of water
initial momentum=[tex]\rho \times A_{inlet}\times V_{inlet}=10^{3}\times \frac{\pi}{4}6^2\times 3^{2}\times 10^{-4}[/tex]
Final Momentum=[tex]\rho \times A_{outlet}\times V_{outlet}=10^{3}\times \frac{\pi}{4}2^2\times 27^{2}\times 10^{-4}[/tex]
Force required=[tex]10^{3}\times \frac{\pi }{4}\times 10^{-4}\left [ 27^{2}\times 2{2}-6{2}\times 3{2}\right ][/tex]=203.60 N