A 12 volt battery in a motor vehicle is capable of supplying the starter motor with 150 A. It is noticed that the terminal voltage of the battery drops to 10 V when the engine is cranked over with the starter motor. Determine the internal resistance of the 12 volt battery.

Answer:

Least velocity.

Explanation:

According to the Bernauli's equation

[tex]p^{2}+\frac{1}{2}\rho v^{2}+\rho gh= constant[/tex]

Here, v is the velocity, m is the mass, h is the height, P is the pressure, [tex]\rho[/tex] is the density

Now according to question.

[tex]P_{1}^{2}+\frac{1}{2}\rho v_{1} ^{2}+\rho gh_{1} =P_{2}^{2}+\frac{1}{2}\rho v_{2} ^{2}+\rho gh_{2}[/tex]

Here airplane height is same means [tex]h_{1}=h_{2}[/tex]  then the required equation will become.

[tex]P_{1}^{2}+\frac{1}{2}\rho v_{1} ^{2}=P_{2}^{2}+\frac{1}{2}\rho v_{2} ^{2}[/tex]

Therefore,

[tex]P_{1}-P_{2}=\frac{1}{2}\rho (v_{2} ^{2}-v_{1} ^{2})[/tex]

Therefore according to the situation [tex]P_{1}>P_{2}[/tex]

This will give the velocity relation [tex]v_{2} >v_{1}[/tex]

Therefore, airplane can fly with least velocity.

Answer:

they meet at distance 25 feet

Explanation:

given data

acceleration of car  = 8 ft/s²

truck speed = 10 ft/s

car initial speed u = 0

truck acceleration = 0

to find out

How far from the starting point will car overtake the truck

solution

we apply here equation of motion

s = ut + 0.5 ×a×t²   .............1

here s is distance and a is acceleration and t is time u is initial speed

so truck distance

s = 10t + 0.5 ×0×t²

s = 10 t   ...............2

and car distance

s = 0+ 0.5 ×8×t²  

s = 4×t²     ..........................3

so from equation 2 and 3

10 t = 4×t²

t = 2.5 s

so both meet at distance

s = 10 (t)

s = 10 ( 2.5 ) = 25 ft

so they meet at distance 25 feet

Answer:

106.52 minutes

Explanation:

Given:

Initial distance between Carl and Isaac = 175 miles

speed of Isaac = 65 mph

Speed of Carl = 50 mph

Now, the Carl starts after 35 minutes, but the Isaac has already started so the distance covered by Isaac in 35 minutes will be

= [tex]\frac{35}{60}\times65[/tex]

= 37.91 miles

Therefore,

the distance left between Isaac and Carl = 175 - 37.91 = 137.09 miles

Since Isaac and Carl are moving towards each other,

therefore the relative speed between the both = 65 + 50 = 115 mph

Hence, the time taken to meet = [tex]\frac{137.09}{115}[/tex]

or

The time taken to meet = 1.192 hours

or

The time taken = 1.192 × 60 = 71.52 minutes

Therefore the total time Isaac have been travelling = 71.52 + 35

= 106.52 minutes

Answer:29.627 m

Explanation:

Given

Initial velocity of life preserver(u) is 1.6 m/s

it takes 2.3 s to reach the water

using equation of motion

v=u+at

[tex]v=1.6+9.81\times 2.3[/tex]

v=24.163 m/s

Let s be the height of life preserver

[tex]v^2-u^2=2gs[/tex]

[tex]24.163^2-1.6^2=2\times 9.81\times s[/tex]

[tex]s=\frac{581.29}{2\times 9.81}[/tex]

s=29.627 m

Answer:3.75 s

Explanation:

Given Body travels half of its motion in last 1.1 sec

Let h be the height and t be the total time taken

here initial velocity is zero

[tex]h=ut+\frac{gt^2}{2}[/tex]

[tex]h=0+\frac{gt^2}{2}[/tex]

[tex]h=\frac{gt^2}{2}------1[/tex]

Now half of the distance traveled will be in t-1.1 s and half distance traveled is in last 1.1 s

[tex]\frac{h}{2}=\frac{g\left ( t-1.1\right )^2}{2}-----2[/tex]

from 1 & 2 we get

[tex]gt^2=2g\left ( t-1.1\right )^2[/tex]

[tex]t^2-4.4t+2.42=0[/tex]

[tex]t=\frac{4.4\pm \sqrt{4.4^2-4\left ( 1\right )\left ( 2.42\right )}}{2}[/tex]

[tex]t=\frac{4.4\pm 3.11}{2}[/tex]

Therefore two value of t is satisfying the equation  but only one value is possible

therefore t=3.75 s

Answer:

yield strength is 64000 lb/ in²

modulus of elasticity is 29.76 ×[tex]10^{6}[/tex] lb/in²

Explanation:

given data

length L = 2 in

area A = 0.5 in²

load = 32000 lb

gage length L1 = 2.0083 in

yield point = 0.2%

maximum load = 60000 lb

to find out

yield strength and modulus of elasticity

solution

we apply here yield strength that is express as

yield strength = [tex]\frac{load}{area}[/tex]  ...........1

yield strength =  [tex]\frac{32000}{0.5}[/tex]

yield strength = 64000 lb/ in²

and

modulus of elasticity  is calculated as

modulus of elasticity =  [tex]\frac{yield strength}{strain}[/tex]    ..........2

here strain = [tex]\frac{L1 - L}{L}[/tex]  

strain = [tex]\frac{2.0083 - 2}{2}[/tex]  

strain = 0.00415

so new strain after offset is here 0.00415 - 0.002

new strain = 0.00215

so from equation 2

modulus of elasticity =  [tex]\frac{yield strength}{strain}[/tex]  

modulus of elasticity =  [tex]\frac{64000}{0.00215}[/tex]  

modulus of elasticity is 29.76 ×[tex]10^{6}[/tex] lb/in²

Final answer:

The yield strength is 64,000 psi, modulus of elasticity is approximately 15.422 x 106 psi, and the tensile strength is 120,000 psi based on the data given from the tensile test of a specimen.

Explanation:

Yield Strength, Modulus of Elasticity, and Tensile Strength

To address the given tensile test problem, we first need to determine the yield strength, which is found by dividing the load at yield by the original area. Hence, the yield strength (\(\sigma_y\)) is 32,000 lb divided by 0.5 in2, which equals 64,000 psi.

The modulus of elasticity (E) can be calculated using Hooke's Law, which is the stress over the strain. In this scenario, the initial stress (\(\sigma_i\)) is the yield load (32,000 lb) over the area (0.5 in2) and the initial strain (\(\epsilon_i\)) is the change in length (0.0083 in) over the original gage length (2.0 in). Therefore, E is 64,000 psi divided by 0.00415, which equals approximately 15,422,000 psi or 15.422 x 106 psi.

As for the tensile strength, it is the maximum stress that the material can withstand while being stretched or pulled before necking, which is the maximum load (60,000 lb) divided by the original cross-sectional area (0.5 in2), which gives us 120,000 psi.

Answer:

The distance is [tex]9.57\times10^{13}\ m[/tex]

Explanation:

Given that,

Diameter of telescope d= 5.08 m

Diameter of sun spot y= 10000 mi

[tex]y =1609.3\times10^{4}\ m[/tex]

We need to calculate the distance

Using formula of distance

[tex]y =\dfrac{1.22\lambda D}{d}[/tex]

[tex]D=\dfrac{d y}{1.22\times\lambda}[/tex]

Put the value into the formula

[tex]D=\dfrac{5.08\times1609.3\times10^{4}}{1.22\times700\times10^{-9}}[/tex]

[tex]D=9.57\times10^{13}\ m[/tex]

Hence, The distance is [tex]9.57\times10^{13}\ m[/tex]

Final answer:

The most distant star on which the Hale Telescope could resolve a sunspot of this size is approximately 73 trillion km away.

Explanation:

To determine the most distant star that this telescope could resolve a sunspot on, we need to calculate the angular resolution of the telescope. The angular resolution of a telescope is given by the formula θ = 1.22 * (λ / D), where θ is the angular resolution, λ is the wavelength of light, and D is the diameter of the telescope's mirror.

To resolve the diameter of a sunspot, we can use the approximate diameter of a large sunspot of 10,000 miles. Converting this to kilometers, we get 16,093.44 km. Assuming an average wavelength of visible light of 550 nm, we can calculate the angular resolution as follows:

θ = 1.22 × (550 nm / 5.08 meters) = 0.013 arc seconds

Now, we need to determine the distance at which this angular resolution corresponds to a sunspot diameter of 16,093.44 km. We can use the small angle formula to calculate the distance:

D = diameter / tan(θ)

D = 16,093.44 km / tan(0.013 arc seconds) = 73,259,925,487,382 km

Therefore, the most distant star on which the Hale Telescope could resolve a sunspot of this size is approximately 73 trillion km away.

Answer:

(a) Projectile B will travel 4 times as far as projectile A prior to landing

Explanation:

Initial velocity = v

Angle at which the projectile is shot at = θ

g = Acceleration due to gravity

Range of a projectile is given by

[tex]R=\frac {v^{2}\sin 2\theta}{g}[/tex]

When Initial velocity = v

[tex]R_A=\frac{v^{2}\sin 2\theta}{g}[/tex]

When Initial velocity = 2v

[tex]R_B=\frac{(2v)^{2}\sin 2\theta}{g}\\\Rightarrow R_B=\frac{4v^2\sin 2\theta}{g}[/tex]

Dividing the equtions, we get

[tex]\frac{R_A}{R_B}=\frac{\frac{v^{2}\sin 2\theta}{g}}{\frac{4v^2\sin 2\theta}{g}}[/tex]

Here, the angle at which the projectiles are fired at are equal.

[tex]\frac{R_A}{R_B}=\frac{1}{4}\\\Rightarrow R_B=4R_A[/tex]

Hence, projectile B will travel 4 times as far as projectile A prior to landing

To compare the ranges of the two projectiles, we can use the fact that the horizontal range of a projectile launched with initial speed [tex]\( v_0 \)[/tex]at an angle [tex]\( \theta \)[/tex] with respect to the horizontal is given by:

[tex]\[ R = \frac{v_0^2 \sin(2\theta)}{g} \][/tex]

Where:

-  R  is the range,

- [tex]\( v_0 \)[/tex] is the initial speed of the projectile,

- [tex]\( \theta \)[/tex] is the launch angle, and

- g is the acceleration due to gravity.

Both projectiles are launched at the same angle with respect to the ground. Since the launch angle is the same for both projectiles, we can compare their ranges by comparing their initial speeds.

Let's denote the range of projectile A as [tex]\( R_A \)[/tex] and the range of projectile B as [tex]\( R_B \).[/tex]

For projectile A:

[tex]\[ R_A = \frac{v^2 \sin(2\theta)}{g} \][/tex]

For projectile B:

[tex]\[ R_B = \frac{(2v)^2 \sin(2\theta)}{g} = 4 \times \frac{v^2 \sin(2\theta)}{g} = 4R_A \][/tex]

So, the range of projectile B is four times the range of projectile A.

Therefore, the correct answer is:

(a) Projectile B will travel 4 times as far as projectile A prior to landing.

Answer:

[tex]h=53.09m[/tex]         (2)

[tex]v_{min}>5.05m/s[/tex]

[tex]v_{max}<10.4m/s[/tex]

Explanation:

a)Kinematics equation for the first ball:

[tex]v(t)=v_{o}-g*t[/tex]

[tex]y(t)=y_{o}+v_{o}t-1/2*g*t^{2}[/tex]

[tex]y_{o}=h[/tex]       initial position is the building height

[tex]v_{o}=8.9m/s[/tex]      

The ball reaches the ground, y=0, at t=t1:

[tex]0=h+v_{o}t_{1}-1/2*g*t_{1}^{2}[/tex]

[tex]h=1/2*g*t_{1}^{2}-v_{o}t_{1}[/tex]           (1)

Kinematics equation for the second ball:

[tex]v(t)=v_{o}-g*t[/tex]

[tex]y(t)=y_{o}+v_{o}t-1/2*g*t^{2}[/tex]

[tex]y_{o}=h[/tex]       initial position is the building height

[tex]v_{o}=0[/tex]       the ball is dropped

The ball reaches the ground, y=0, at t=t2:

[tex]0=h-1/2*g*t_{2}^{2}[/tex]

[tex]h=1/2*g*t_{2}^{2}[/tex]         (2)

the second ball is dropped a time of 1.03s later than the first ball:

t2=t1-1.03              (3)

We solve the equations (1) (2) (3):

[tex]1/2*g*t_{1}^{2}-v_{o}t_{1}=1/2*g*t_{2}^{2}=1/2*g*(t_{1}-1.03)^{2}[/tex]

[tex]g*t_{1}^{2}-2v_{o}t_{1}=g*(t_{1}^{2}-2.06*t_{1}+1.06)[/tex]

[tex]g*t_{1}^{2}-2v_{o}t_{1}=g*(t_{1}^{2}-2.06*t_{1}+1.06)[/tex]

[tex]-2v_{o}t_{1}=g*(-2.06*t_{1}+1.06)[/tex]

[tex]2.06*gt_{1}-2v_{o}t_{1}=g*1.06[/tex]

[tex]t_{1}=g*1.06/(2.06*g-2v_{o})[/tex]

vo=8.9m/s

[tex]t_{1}=9.81*1.06/(2.06*9.81-2*8.9)=4.32s[/tex]

t2=t1-1.03              (3)

t2=3.29sg

[tex]h=1/2*g*t_{2}^{2}=1/2*9.81*3.29^{2}=53.09m[/tex]         (2)

b)[tex]t_{1}=g*1.06/(2.06*g-2v_{o})[/tex]

t1 must :   t1>1.03  and t1>0

limit case: t1>1.03:

[tex]1.03>9.81*1.06/(2.06*g-2v_{o})[/tex]

[tex]1.03*(2.06*9.81-2v_{o})<9.81*1.06[/tex]

[tex]20.8-2.06v_{o}<10.4[/tex]

[tex](20.8-10.4)/2.06<v_{o}[/tex]

[tex]v_{min}>5.05m/s[/tex]

limit case: t1>0:

[tex]g*1.06/(2.06*g-2v_{o})>0[/tex]

[tex]2.06*g-2v_{o}>0[/tex]

[tex]v_{o}<1.06*9.81[/tex]

[tex]v_{max}<10.4m/s[/tex]

Answer:

58.703 ft/centuri

Explanation:

Length of the hair grow, l = 0.49 mm

Time to grow, t = 1 day

Convert mm into feet.

We know that, 1 mm = 0.00328 feet

So, 0.49 mm = 0.49 x 0.00328 = 0.0016072 ft

Convert day into century.

We know that, 1 century = 36525 days

So, 1 day = 1 / 36525 centuri

growth rate of hair =  [tex]\frac{0.0016072}{\frac{1}{36525}}[/tex]

                               = 58.703 ft/centuri

Answer:

129 m because the average velocity is 13.9 m/s, the change in velocity

divided by the acceleration is the time, and the time multiplied by the

average velocity is the distance. ⇒ answer C

Explanation:

Lets explain how to solve the problem

The given is:

The care is able to stop with an acceleration of -3 m/s²

→ The final velocity = 0 and acceleration = -3 m/s²

Calculate the distance required to stop from a velocity of 100 km/h

→ Initial velocity = 100 km/h

At first we must to change the unite of the initial velocity from km/h

to m/s because the units of the acceleration is m/s²

→ 1 km = 1000 meters and 1 hr = 3600 seconds

→ 100 km/h = (100 × 1000) ÷ 3600 = 27.78 m/s

The initial velocity is 27.78 m/s

Acceleration is the rate of change of velocity during the time,

then the time is the change of velocity divided by the acceleration

→ [tex]t=\frac{v-u}{a}[/tex]

where v is the final velocity, u is the initial velocity, t is the time and

a is the acceleration

→ v = 0 , u = 27.78 m/s , a = -3 m/s²

Substitute these values in the rule

→ [tex]t=\frac{0-27.78}{-3}=9.26[/tex] seconds

The time to required stop is 9.26 seconds

We can calculate the distance by using the rule:

→ s = ut + [tex]\frac{1}{2}[/tex] at²

→ u = 27.78 m/s , t = 9.26 s , a = -3 m/s²

Substitute these values in the rule

→ s = 27.78(9.26) + [tex]\frac{1}{2}[/tex] (-3)(9.26) = 128.6 ≅ 129 m

The distance required to stop is 129 m

Average velocity is total distance divided by total time

→ Total distance = 129 m and total time = 9.26 s

→ average velocity = 129 ÷ 9.26 = 13.9 m/s

The average velocity is 13.9 m/s

So the time multiplied by the average velocity is the distance

The answer is C

129 m because the average velocity is 13.9 m/s, the change in

velocity divided by the acceleration is the time, and the time

by the average velocity is the distance.

Two points are given in polar coordinates,  the distance between the two points is approximately 3.12m.

You can use the polar-to-cartesian conversion formula to convert each point to Cartesian coordinates (x, y), then apply the distance formula in

Cartesian coordinates to determine the separation between two points supplied in polar coordinates.

The polar-to-cartesian conversion formulas are:

[tex]\[ x = r \cdot \cos(\theta) \][/tex]

[tex]\[ y = r \cdot \sin(\theta) \][/tex]

Given the points:

[tex]\( (r_1, \theta_1) = (2.60 \, \text{m}, 50.0^\circ) \)[/tex]

[tex]\( (r_2, \theta_2) = (3.60 \, \text{m}, -46.0^\circ) \)[/tex]

Converting these points to Cartesian coordinates:

For the first point:

[tex]\[ x_1 = 2.60 \, \text{m} \cdot \cos(50.0^\circ) \approx 1.66 \, \text{m} \][/tex]

[tex]\[ y_1 = 2.60 \, \text{m} \cdot \sin(50.0^\circ)\\\\ \approx 1.98 \, \text{m} \][/tex]

For the second point:

[tex]\[ x_2 = 3.60 \, \text{m} \cdot \cos(-46.0^\circ)\\\\ \approx 2.53 \, \text{m} \][/tex]

[tex]\[ y_2 = 3.60 \, \text{m} \cdot \sin(-46.0^\circ)\\\\ \approx -2.57 \, \text{m} \][/tex]

Now, you can use the distance formula in Cartesian coordinates to find the distance between the two points:

[tex]\[ \text{distance} = \sqrt{(x_2 - x_1)^2 + (y_2 - y_1)^2} \][/tex]

Plug in the values and calculate:

[tex]\[ \text{distance} = \sqrt{(2.53 \, \text{m} - 1.66 \, \text{m})^2 + (-2.57 \, \text{m} - 1.98 \, \text{m})^2}\\\\ \approx 3.12 \, \text{m} \][/tex]

Thus, the distance between the two points is approximately 3.12 m.

For more details regarding Cartesian coordinates, visit:

https://brainly.com/question/30637894

#SPJ12

Answer:

The spring constant k is[tex]1.115\times 10^{9} N/m[/tex]

Solution:

As per the question:

Length of the solid cylinder, L = 500 mm = [tex]500\times 10^{- 3} = 0.5 m[/tex]

Diameter pf the cylinder, D = 2 cm = 0.02 m

As the radius is half the diameter,

Radius, R = 1 cm = 0.01 m

Young's Modulus, E = 17.4 GPa = [tex]17.4\times 10^{9} Pa[/tex]

Now,

The relation between spring constant, k and Young's modulus:

[tex]kL = EA[/tex]

where

A = Area

Area of solid cylinder, A = [tex]2\piR(L + R)[/tex]

[tex]0.5k = 17.4\times 10^{9}\times 2\piR(L + R)[/tex]

[tex]k = \frac{17.4\times 10^{9}\times 2\pi\times 0.01(0.01 + 0.5)}{0.5}[/tex]

k = [tex]1.115\times 10^{9} N/m[/tex]

Young's modulus, E is the ratio of stress and strain

And

Stress = [tex]\frac{Force or thrust}{Area}[/tex]

Strain = [tex]\frac{length, L}{elongated or change in length, \Delta L}[/tex]

Also

Force on a spring is - kL

Therefore, we utilized these relations in calculating the spring constant.

Answer:

F = -10800 N

Explanation:

Given that,

Charge 1, [tex]q_1=-1.5\ C[/tex]

Charge 2, [tex]q_2=0.8\ C[/tex]

Distance between the charges, [tex]d=1\ km=10^3\ m[/tex]

We need to find the electric force acting between two point charges. Mathematically, it is given by :

[tex]F=k\dfrac{q_1q_2}{d^2}[/tex]

[tex]F=-9\times 10^9\times \dfrac{1.5\times 0.8}{(10^3)^2}[/tex]

F = -10800 N

So, the magnitude of electric force between two point charges is 10800 N. Hence, this is the required solution.

Answer:

93.29 gallons

Explanation:

Given:

Number of solar panels = 3

Area of each solar panel = 1 m × 2 m = 2 m²

Total area of solar panels = 3 × 2 = 6 m²

Time = 4 hrs = 4 × 60 × 60 = 14400 seconds

Change in temperature, ΔT = 120° C - 40° C = 80° C

Now,

the solar power received on the Earth = 1368 W/m²

Thus,

The Heat energy received = Power × Area × Time

or

The Heat energy received = 1368 × 6 × 14400 =  118195200 J

Also,

Heat = mCΔT

where, C is the specific heat of the water

m is the mass of the water = 4.184 J/g.C

thus,

118195200 J = m × 4.184 × 80

or

mass of water that can be heated, m = 353116.63 grams = 353.116 kg

Also,

1 gallon of water = 3.785 kg

thus,

1 kg of water = 0.2642 gallons

Hence,

353.116 kg of water = 93.29 gallons

i.e 93.29 gallons of water can be heated

To determine how many gallons of water can be heated from 40°C to 120°C by three solar panels, we must calculate the energy absorbed by the panels using insolation data and then apply the specific heat capacity of water. The actual insolation value is necessary for the precise calculation, which was not provided in the question.

The amount of water that can be heated from 40°C to 120°C each day by solar panels can be calculated using principles from physics, specifically thermodynamics and energy transfer. First, we need to determine the energy incident on the solar panels. Assuming normally incident sunlight for 4 hours and a total solar panel area of 6 m² (as there are three 1 m x 2 m panels), we can calculate the energy absorbed.

Next, we use the specific heat capacity equation to find how much water this energy can heat from 40°C to 120°C. The specific heat capacity of water is approximately 4.18 J/g°C. Afterwards, we'll convert this amount of water from liters (or kilograms, as 1 L of water is approximately 1 kg) into gallons for the answer.

To complete this calculation, we would need to know the actual insolation in the specific location in terms of energy per unit area per unit time (e.g., kW/m²), which is not provided in the question or the reference material. But, if we assume insolation similar to the examples given in the reference material, we could use that to approximate the answer.

Answer:

intensity of sound at level of microphone is 0.00139 W / m 2

sound intensity level at position of micro phone is 91.456 dB

EXPLANATION:

Given data:

power of sound   P = 31 W

distance betwen microphone & speaker is   42 m

a) intensity of sound at microphone is calculated as

                   [tex]I = \frac{P}{A}[/tex]

                   [tex]= \frac{34}{4 \pi ( 44m )^ 2}[/tex]

                   =  0.00139 W / m 2        

b) sound intensity level at position of micro phone is

                [tex]\beta = 10 log \frac{I}{I_o}[/tex]

    where I_o id reference sound intensity and taken as

                [tex]= 1 * 10^{-12} W / m 2[/tex]  

               [tex]\beta = 10 log\frac{0.00139}{10^[-12}}[/tex]

                     = 91.456 dB

Answer:

zero, acceleration due to gravity = 9.8 m/s^2

Explanation:

When an object throws vertically upwards, the acceleration acting on the object is acceleration due to gravity which is acting in vertically downwards direction.

As the object moves upwards, its velocity goes on decreasing because the direction of velocity and the acceleration both are opposite to each other. At maximum height, the velocity of object becomes zero and then object starts moving in downwards direction.

Thus, the value of instantaneous velocity at maximum height is zero but the vale of acceleration is acceleration due to gravity which is acting vertically downward direction.

Answer:

value of the acceleration of gravity on the planet is 5.00 m/s²

Explanation:

The problem is similar to a free fall exercise, with another gravity value, the expression they give us is the following:

       y-yo = ½ gₐ t²       (1)

They tell us that they make a squared time graph with the variation of the distance, it is appropriate to clarify this in a method to linearize a curve, which is plotted the nonlinear axis to the power that is raised, specifically, the linearization of a curve The square is plotted against the other variable.

  Let's continue our analysis, as we have a linear equation, write the equation of the line.

        y1 = m x1 + b       (2)

where  “y1” the dependent variable, “x1” the independent variable, “m” the slope and “b” the short point

In this case as the stone is released its initial velocity is zero which implies that b = 0,

We plot on the “y” axis the time squared “t²” and on the horizontal axis we place “y-yo”.  To better see the relationship we rewrite equation 1 with this form

        t² = 2 /gₐ  (y-yo)

With the two expressions written in the same way, let's relate the terms one by one

        y1 = t²

        x1 = (y-yo)

        m = 2/gap

        b= 0

We substitute and calculate

        m = 2/gp

        gₐ = 2/m

        gₐ = 2/ 0.400

        gₐ = 5.00 m / s²

This is the value of the acceleration of gravity on the planet, note that the decimals are to keep the figures significant

Explanation:

Instantaneous velocity is specific rate of the change of the position or the displacement with respect to the time at a particular single point (x,t)

[tex]v(t)=\frac{d}{dt}x(t)[/tex]

Average velocity is average rate of the change of the position or the displacement with respect to the time over an particular interval.

[tex]{v}=\frac {\Delta x}{\Delta t}=\frac{{x}_{\text{f}}-{x}_{\text{i}}}{{t}_{\text{f}}-{t}_{\text{i}}}[/tex]

Answer:

Case I: 12.617 L/s

Case II: 161.406 cubic meters per hour

Case III: 1.062 Pound inches

Explanation:

Given:

Assumptions:

Case I:

[tex]Speed\ of\ water\ flow = 200 \dfrac{gallon}{min}\\\Rightarrow V_{water} = 200\times \dfrac{3.785\ L}{60\ s}\\\Rightarrow V_{water} = 12.617\ L/s[/tex]

Case II:

[tex]Speed\ of\ air\ blow = 95 \dfrac{ft^3}{min}\\\Rightarrow V_{air} = 95\times \dfrac{(0.3048\ m)^3}{\dfrac{1}{60}\ h}\\\Rightarrow V_{air} = 95\times (0.3048)^3\times 60\ m^3/h\\\Rightarrow V_{air} = 161.406\ m^3/h[/tex]

Case III:

[tex]Measure\ of\ torque = 12\ N cm\\\Rightarrow \tau = 12\times (0.2248\ lb)\times \dfrac{1}{2.54}\ in\\ \Rightarrow \tau = 1.062\ lb in[/tex]

Answer:

Vmax = 12.21m/s

[tex]a = 4.07m/s^{2}[/tex]

Explanation:

For the first 3 seconds:

[tex]V_{3}=V_{o}+a*t=0+a*3=3a[/tex]   This is the maximum speed. But we need acceleration.

[tex]X_{3}=V_{o}*t+\frac{a*t^{2}}{2} =\frac{9*a}{2}[/tex]

For the other 6.69s with constant speed:

[tex]X_{t}=100=X_{3}+V_{3}*t[/tex]

[tex]100=\frac{9*a}{2} +3*a*6.69[/tex]   Solving for a:

[tex]a = 4.07m/s^{2}[/tex]  Now we replace this value on [tex]V_{3}=3a[/tex]:

[tex]V_{3}=V_{max}=12.21m/s[/tex]

A molecule of hydrogen moving at a speed of 115 cm/s would take approximately 79.5 seconds to travel the length of a football field (100 yd).

To compute the time it would take a molecule of hydrogen to move the length of a football field, you would use the formula time = distance/speed. However, we must first convert the length of the football field from yards to centimeters for consistency.

One yard is approximately 91.44 cm, so a football field which is 100 yards is about 9144 cm. Using the given speed of a hydrogen molecule which is 115 cm/s, the time it would take can be computed as follows: time = 9144 cm / 115 cm/s = approx. 79.5 seconds.

https://brainly.com/question/31756299

#SPJ12

Answer:

Charge on A is [tex]q=0.7820\times 10^{-5}C[/tex]

Charge on B is [tex]2q=2\times 0.7820\times 10^{-5}C=1.5640\times 10^{-5}C[/tex]  

Explanation:

We have given one charge is twice of other charge

Let [tex]q_1=q[/tex], then [tex]q_2=2q[/tex]

Distance between two charges = 16 cm = 0.16 m

Force F = 43 N

According to coulombs law force between tow charges is given by

[tex]F=\frac{1}{4\pi \epsilon _0}\frac{q_1q_2}{r^2}=\frac{Kq_1q_2}{r^2}[/tex], here K is constant which value is [tex]9\times 10^9[/tex]

So [tex]43=\frac{9\times 10^92q^2}{0.16^2}[/tex]

[tex]q^2=0.0611\times 10^{-9}[/tex]

[tex]q^2=0.611\times 10^{-10}[/tex]

[tex]q=0.7820\times 10^{-5}C[/tex] so charge on A is [tex]q=0.7820\times 10^{-5}C[/tex]

And charge on B is [tex]2q=2\times 0.7820\times 10^{-5}C=1.5640\times 10^{-5}C[/tex]

The magnitudes of the charges are:

Charge A: [tex]\underline {1.10 \times 10^{-5} \text{C}}[/tex].

Charge B: [tex]\underline {5.52 \times 10^{-6} \text{C}}[/tex]

Use Coulomb's Law, which states:

[tex]F = k \frac{ |q_1 \, q_2| }{ r^2 }[/tex]

where:

Given:

Let's substitute these values into Coulomb's Law:

[tex]43.0 \; \text{N} = (8.99 \times 10^9 \; \text{Nm}^2/\text{C}^2) \frac{ |2q \cdot q| }{ (0.16 \; \text{m})^2 }[/tex]

Simplify the equation:

[tex]43.0 \; \text{N} = (8.99 \times 10^9) \frac{ 2q^2 }{ 0.0256 } \text{Nm}^2/\text{C}^2[/tex]

[tex]43.0 \; \text{N} = ( 7.03 \times 10^{11} ) 2q^2[/tex]

Solving for [tex]q^2[/tex]:

[tex]43.0 = 1.406 \times 10^{12} q^2[/tex]

[tex]q^2 = \frac{ 43.0 }{ 1.406 \times 10^{12} }[/tex]

[tex]q = \sqrt{ \frac{ 43.0 }{ 1.406 \times 10^{12} } }[/tex]

[tex]q \approx 5.52 \times 10^{-6} \text{C}[/tex]

This gives us the magnitude of charge B [tex]q_2[/tex].

Since [tex]q_1 = 2q_2[/tex]:

Charge A: [tex]q_1 = 2 \times 5.52 \times 10^{-6} \text{C} = 1.10 \times 10^{-5} \text{C}[/tex]

Charge B: [tex]q_2 = 5.52 \times 10^{-6} \text{C}[/tex]

Answer:

The total electric potential at mid way due to 'q' is [tex]\frac{q}{4\pi\epsilon_{o}d}[/tex]

The net Electric field at midway due to 'q' is 0.

Solution:

According to the question, the separation between two parallel plates, plate A and plate B (say)  = d

The electric potential at a distance d due to 'Q' is:

[tex]V = \frac{1}{4\pi\epsilon_{o}}.\frac{Q}{d}[/tex]

Now, for the Electric potential for the two plates A and B at midway between the plates due to 'q':

For plate A,

[tex]V_{A} = \frac{1}{4\pi\epsilon_{o}}.\frac{q}{\frac{d}{2}}[/tex]

Similar is the case with plate B:

[tex]V_{B} = \frac{1}{4\pi\epsilon_{o}}.\frac{q}{\frac{d}{2}}[/tex]

Since the electric potential is a scalar quantity, the net or total potential is given as the sum of the potential for the two plates:

[tex]V_{total} = V_{A} + V_{B} = \frac{1}{4\pi\epsilon_{o}}.q(\frac{1}{\frac{d}{2}} + \frac{1}{\frac{d}{2}}[/tex]

[tex]V_{total} = \frac{q}{4\pi\epsilon_{o}d}[/tex]

Now,

The Electric field due to charge Q at a distance is given by:

[tex]\vec{E} = \frac{1}{4\pi\epsilon_{o}}.\frac{Q}{d^{2}}[/tex]

Now, if the charge q is mid way between the field, then distance is [tex]\frac{d}{2}[/tex].

Electric Field at plate A, [tex]\vec{E_{A}}[/tex] at midway due to charge q:

[tex]\vec{E_{A}} = \frac{1}{4\pi\epsilon_{o}}.\frac{q}{(\frac{d}{2})^{2}}[/tex]

Similarly, for plate B:

[tex]\vec{E_{B}} = \frac{1}{4\pi\epsilon_{o}}.\frac{q}{(\frac{d}{2})^{2}}[/tex]

Both the fields for plate A and B are due to charge 'q' and as such will be equal in magnitude with direction of fields opposite to each other and hence cancels out making net Electric field zero.

Answer:

The magnitude of force is [tex]4.26\times 10^{- 6} N[/tex]

Solution:

As per the question:

The strength of Electric field due west at a certain point, [tex]\vec{E_{w}} = 710,000 N/C[/tex]

Charge, Q = - 6 C

Now, the force acting on the charge Q in the electric field is given by:

[tex]\vec{F} = Q\vec{E_{w}}[/tex]

[tex]\vec{F} = -6\times 710,000 = - 4.26\times 10^{- 6} N[/tex]

Here, the negative sign indicates that the force acting is opposite in direction.

Answer:

Explanation:

Spring constant k = 5N/m

I ) x = 3 m means , spring is stretched by 3 m  

Restoring force by spring = kx = 5 x 3 = 15 N

II )  When mass is touching the wall, extension in spring = 1 m

Force by spring on the body

= 1 x 5 = 5 N .

iii ) . It is touching the wall , x =  1 m

Stored energy in the spring = 1/2 k x² = .5 x 5 x 1 x 1

= 2.5 J

When x = 3 , energy stored in it

Potential energy stored in it = 1/2 k x²

= .5 x 5 x 3 x 3

= 22.5 J

Increase in stored energy = 22.5 - 2.5

20 J

This must be the work done to stretch it from 1 m to 3 m .

Answer:

Image is virtual and formed on the same side as the object, 19.29 cm from the lens.

The height of the image is 0.40509 cm

Image is upright as the magnification is positive and smaller than the object.

Explanation:

u = Object distance =  100 cm

v = Image distance

f = Focal length = -23.9 cm (concave lens)

[tex]h_u[/tex]= Object height = 2.1 cm

Lens Equation

[tex]\frac{1}{f}=\frac{1}{u}+\frac{1}{v}\\\Rightarrow \frac{1}{f}-\frac{1}{u}=\frac{1}{v}\\\Rightarrow \frac{1}{v}=\frac{1}{-23.9}-\frac{1}{100}\\\Rightarrow \frac{1}{v}=\frac{-1239}{23900} \\\Rightarrow v=\frac{-23900}{1239}=-19.29\ cm[/tex]

Image is virtual and formed on the same side as the object, 19.29 cm from the lens.

Magnification

[tex]m=-\frac{v}{u}\\\Rightarrow m=-\frac{-19.29}{100}\\\Rightarrow m=0.1929[/tex]

[tex]m=\frac{h_v}{h_u}\\\Rightarrow 0.1929=\frac{h_v}{2.1}\\\Rightarrow h_v=0.1929\times 2.1=0.40509\ cm[/tex]

The height of the image is 0.40509 cm

Image is upright as the magnification is positive and smaller than the object.

Answer:

after 6 second it will stop

he travel 36 m to stop

Explanation:

given data

speed = 12 m/s

distance = 100 m

decelerates rate = 2.00 m/s²

so acceleration a = - 2.00 m/s²

to find out

how long does it take to stop and how far does he travel

solution

we will apply here first equation of motion that is

v = u + at   ......1

here u is speed 12 and v is 0 because we stop finally

put here all value in equation 1

0 = 12 + (-2) t

t = 6 s

so after 6 second it will stop

and

for distance we apply equation of motion

v²-u² = 2×a×s  ..........2

here v is 0 u is 12 and a is -2 and find distance s

put all value in equation 2

0-12² = 2×(-2)×s

s = 36 m

so  he travel 36 m to stop

Answer:

a)Q= + 0.71 nC , For the resultant electric field at the origin to be 45.0 N/C in the +x direction

b)Q= -2.83nC ,for the resultant electric field at the origin to be 45.0 N/C in the −x direction

Explanation:

Conceptual analysis

The electric field at a point P due to a point charge is calculated as follows:

E = k*q/d²

E: Electric field in N/C

q: charge in Newtons (N)

k: electric constant in N*m²/C²

d: distance from charge q to point P in meters (m)

The electric field at a point P due to several point charges is the vector sum of the electric field due to individual charges.

Equivalences

1nC= 10⁻9 C

Data

k = 8.99*10⁹ N×m²/C²

q₁ =+5.45nC = 3*10⁻⁹C

d₁ =1.35 m

d₂ = 0.595m

a)Problem development : sign and magnitude of Q for the resultant electric field at the origin to be 45.0 N/C in the +x direction

We make the algebraic sum of fields at at the origin :

[tex]E_{o} =E_{q} +E_{Q}[/tex] Equation (1)

[tex]E_{q} =\frac{k*q_{1} }{d_{1}{2}  }[/tex]

Calculation of E(q)

[tex]E_{q} =\frac{8.99*10^{9} *5.45*10^{-9} }{1,35^{2} }[/tex]

[tex]E_{q} =26.88\frac{N}{C}[/tex] : in the +x direction .As the charge is negative, the field enters the charge

We replace [tex]E_{o}[/tex] and [tex]E_{q}[/tex] in the equation (1)

[tex]45=26.88+E_{Q}[/tex]

[tex]E_{Q} =45-26.88[/tex]

[tex]E_{Q} = 18.12 N/C[/tex] : in the +x direction .

Sign and magnitude of Q

Q must be positive for the field to abandon the load in the +x

[tex]E_{Q} =\frac{k*Q}{d_{2}^{2} }[/tex]

[tex]18.12=\frac{8.99*10^{9}*Q }{0.595^{2} }[/tex]

[tex]Q=\frac{18.12*0.595^{2} }{8.99*10^{9} }[/tex]

Q=0.71*10⁻⁹ C =0.71 nC

b)Sign and magnitude of Q for the resultant electric field at the origin to be 45.0 N/C in the −x direction

We make the algebraic sum of fields at at the origin :

[tex]E_{o} =E_{q} +E_{Q}[/tex]

[tex]-45=26.88+E_{Q}[/tex]

[tex]-71.88=E_{Q}[/tex]

[tex]71.88=\frac{8.99*10^{9} *Q}{0.595^{2} }[/tex]

Q= 2.83*10⁻⁹ C

Q= -2.83nC

Q must be negative for the field to enters the charge in the −x direction

The magnitude and sign of Q is given by the required magnitude and

sign of the charge at the origin due to the sum of the charges.

Responses:

The charge at the origin is given as follows;

When the charge at the origin is 45.0 N/C, we have;

[tex]45 = \mathbf{\dfrac{8.99 \times 10^{9} \times -5.45 \times ^{-9} }{1.35^2} + \dfrac{8.99 \times 10^{9} \times Q} {(-0.595)^2}}[/tex]

Which gives;

[tex]Q = \dfrac{\left(45 - \dfrac{8.99 \times 10^{9} \times -5.45 \times ^{-9} }{1.35^2} \right) \times (-0.595)^2}{8.99 \times 10^{9} } \approx \mathbf{2.83 \times 10^{-9}}[/tex]

When the charge at the origin is [tex]E_0[/tex] = 45 N/C, we have;

When the charge at the origin is [tex]E_0[/tex] = 45 N/C in the -x direction, we have;

[tex]Q = \dfrac{\left(-45 - \dfrac{8.99 \times 10^{9} \times -5.45 \times ^{-9} }{1.35^2} \right) \times (-0.595)^2}{8.99 \times 10^{9} } \approx -7.134 \times 10^{-10}[/tex]

Therefore;

The charge at the origin is [tex]E_0[/tex] = 45 N/C in the -x direction, we have;

Learn more about electric field strength here:

https://brainly.com/question/12644782

Answer:

216480000 fathoms

Explanation:

1 fathom = 6 feet

[tex]1\ feet=\frac{1}{6}\ fathom[/tex]

Distance from Earth to the Moon = 246000 miles

Converting to feet

1 mile = 5280 feet

246000 miles = 1298880000 feet

Convert to fathom

[tex]1\ feet=\frac{1}{6}\ fathom\\\Rightarrow 1298880000\ feet=\frac{1298880000}{6}=216480000\ fathom[/tex]

So, the distance between Earth and Moon is 216480000 fathoms