Please help! A net force of 2.0 N acts on a 2.0-kg object for 10 seconds. What is the object’s kinetic energy after that 10 seconds (assuming the object starts from rest and there is no friction)?

Answers

Answer 1

For Newton's second law, the force F applied to the object of mass m will cause an acceleration a of the body:
[tex]F=ma[/tex]
So, the acceleration is
[tex]a= \frac{F}{m}= \frac{2.0 N}{2.0 kg}=1 m/s^2 [/tex]

The object undergoes through this acceleration for 10 seconds, t=10 s. Since it is an accelerated motion, we can find its final velocity after 10 seconds:
[tex]v_f = v_i + at=0 m/s+(1m/s^2)(10 s)=10 m/s[/tex]
where [tex]v_i[/tex] is the initial velocity of the object, which is zero since it starts from rest.

Finally we can calculate the final kinetic energy of the object, which is given by
[tex]K= \frac{1}{2}mv^2= \frac{1}{2}(2.0 kg)(10 m/s)^2=100 J [/tex]

Related Questions

The input force of a pulley system must move 8.0 m to lift a 3,000-n engine a distance of 2.0 m. what is the ima of the system?

Answers

The IMA (ideal mechanical advantage) of a single pulley is the ratio between the output force and the input force:
[tex]IMA= \frac{F_{out}}{F_{in}} [/tex]
Moreover, for the law of conservation of energy, the work done in input to lift the lift must be equal to the output work:
[tex]W_{in}=W_{out}[/tex]
[tex]F_{in} d_{in}=F_{out} d_{out}[/tex]
where the [tex]d_{in}[/tex] is the distance for which the input force is applied while [tex]d_{out}[/tex] is the distance of which the lift is lifted.
Substituting [tex]F_{out}=3000 N[/tex], [tex]d_{out}=2 m[/tex] and [tex]d_{in}=8 m[/tex] into the previous equation, we find the value of the input force:
[tex]F_{in}= \frac{F_{out} d_{out}}{d_{in}} = \frac{(3000 N)(2 m)}{8 m}=750 N [/tex]
And now we can find the IMA of the pulley:
[tex]IMA= \frac{F_{out}}{F_{in}}= \frac{3000 N}{750 N}=4 [/tex]

As we can see, the IMA is also equal to the ratio between the input and output distance:
[tex]IMA= \frac{d_{in}}{F_{out}}= \frac{8m}{2m}=4 [/tex]

The potential difference in a simple circuit is 9 v and the resistance is 47 ω . what current flows in the circuit? answer in units of
a.

Answers

The current flowing in the circuit with a potential difference of 9 volts and resistance of 47 ohms is approximately 0.1915 amperes (A), calculated using Ohm's Law (I = V/R).

The current that flows through a circuit can be calculated using Ohm's Law, which is given by the formula V = IR, where V is the potential difference, I is the current, and R is the resistance. In this case, the potential difference is 9 volts (V) and the resistance is 47 ohms (Ω). To find the current, we rearrange the formula to I = V/R.

Substitute the given values into the formula:

I = 9V / 47Ω

I ≈ 0.1915 A

So the current flowing in the circuit is approximately 0.1915 amperes (A).

the combination of all forces acting on an object is called _____.

Answers

The answer is net force akaskakska

Match the description of how heat is transferred to the proper term. A. When two things in contact with each other transfer heat Convection B. When a liquid or gas carries heat Conduction C. When waves transfer heat Radiation

Answers

When two things in contact with each other transfer heat - Conduction
When a liquid or has carries heat- Convection
When waves transfer heat- Radiation

these are my answers from the quiz i took

Record the length of the line shown in millimeters.

Choose one will mark the Brainliest.

34.3

3.43

3.40

3.4

Answers

Boss, your ruler is in centimeters which means it’s roughly 34 mm

This line is measured on a cm scale and we need to convert to mm. To do that multiply the cm by 10.
When I look at the line the length is approximately 3.4 cm multiply that by 10 to get roughly 34 mm which matches with a

How was the speed of light measured in a precise way?

A. by timing how long it takes for an assistant far away to turn on a lantern after the scientist turns one on

B. by watching for eclipses

C. by timing the speed of falling meteorites

D. by using rotating mirrors to measure light's round trip travel to a distant mountain

:O :/,

Answers

The first successful measurement of the speed of light was done so through the observation of eclipses. Olaus Roemer noticed that depending on the relationship between the Earth, Sun and Jupiter there were varying differences in the times of predicted eclipses.

Particle q₁ has a charge of 2.7 μC and a velocity of 773 m/s. If it experiences a magnetic force of 5.75 × 10⁻³ N, what is the strength of the magnetic field?
A. 0.36 T
B. 1.6 T
C. 2.8 T

In the same magnetic field, particle q₂ has a charge of 42.0 μC and a velocity of 1.21 × 10³ m/s. What is the magnitude of the magnetic force exerted on particle 2?
A. 0.042 N
B. 0.12 N
C. 0.14 N

Answers

The intensity of the magnetic force F experienced by a charge q moving with speed v in a magnetic field of intensity B is equal to
[tex]F=qvB \sin \theta[/tex]
where [tex]\theta[/tex] is the angle between the directions of v and B.

1) Re-arranging the previous formula, we can calculate the value of the magnetic field intensity. The charge is [tex]q=2.7 \mu C=2.7 \cdot 10^{-6}C[/tex]. In this case, v and B are perpendicular, so [tex]\theta=90^{\circ}[/tex], therefore we have:
[tex]B= \frac{F}{qv \sin \theta} = \frac{5.75 \cdot 10^{-3}N}{(2.7 \cdot 10^{-6}C)(773m/s)\sin 90^{\circ}}=2.8 T [/tex]

2) In this second case, the angle between v and B is [tex]\theta=55^{\circ}[/tex]. The charge is now [tex]q=42.0 \mu C=42.0 \cdot 10^{-6}C[/tex], and the magnetic field is the one we found in the previous part, B=2.8 T, so we can find the intensity of the force experienced by this second charge:
[tex]F=qvB \sin \theta=(42\cdot 10^{-6}C)(1.21 \cdot 10^3 m/s)(2.8 T)(\sin 55^{\circ})=0.12 N[/tex]

Answer:

1. 2.8

2. 0.12

Explanation:

The temperature differences seen between quito, ecuador, and guayaquil, ecuador, illustrate the effect of _____. ocean currents cloud cover altitude

Answers

The answer would be altitude.
Quito has the altitude of 2.850m, while Guayaquil has the altitude of 5m.
This can lead to the vast difference in climates.
The most noticeable difference is that temperature drop with increased altitude.
For each 1,000 foot rise in altitude, there is a 4°F drop in temperature.

This one has got to be the altitude.

PART 2!!!! PLEASEEEE HELLLPPPP

Answers

I see three (3) question in the picture.
Here are the answers:

#1).
The total effective resistance of resistors in series is
the sum of the individuals.

(4 + 8 + 12) = 24 ohms.

Current = (voltage) / (resistance) = (24 V) / (24 ohms) = 1 Ampere.

#2).
To answer this question, we don't care what the
total effective resistance is.
The resistors are in parallel, so each one is connected
directly to the terminals of the battery, and each resistor
has 24 V across it.

Current through the 4-ohm resistor = (voltage) / (resistance)

= (24 V) / (4 ohms)

= 6 Amperes.

#3).
In a series circuit, the total effective resistance is
the sum of the individual resistors, and the current
is (battery voltage) / (total effective resistance).

If pone resistor is replaced with a resistor of lower resistance,
then the sum of the individuals is less, and the current in the
series circuit increases (if the battery can handle it).

A balloon filled with helium occupies 20.0 l at 1.50 atm and 25.0◦
c. how many moles of helium will there be in the balloon at stp?

Answers

Final answer:

By applying the Ideal Gas Law, we find that the helium balloon contains approximately 1.22 moles under the given conditions. This mole amount remains consistent at standard temperature and pressure (STP) as no gas is added or removed.

Explanation:

Your question pertains to the concepts of chemical stoichiometry and the gas laws. Given the conditions and the volume of the gas, we start by converting the initial conditions to Standard Temperature and Pressure (STP). Your balloon containing helium is at a volume of 20.0 L, a pressure of 1.50 atm, and a temperature of 25.0°C (or 298.15 K in absolute temperature).

The Ideal Gas Law (PV=nRT) allows us to calculate the number of moles (n) in the balloon initially: n = PV/RT = (1.50 atm * 20.0 L) / (0.0821 L*atm/mol*K * 298.15 K) which results in approximately 1.22 mol of helium.

Now, to find the number of moles at STP, we need to remember that the number of moles remains the same as long as no gas is added or removed. Therefore, your balloon contains approximately 1.22 moles of helium at STP as well.

Learn more about Calculation of Helium Moles here:

https://brainly.com/question/37979966

#SPJ12

There are approximately [tex]1.225\ moles[/tex] of helium in the balloon at STP (Standard Temperature and Pressure).

To find out how many moles of helium are in the balloon at STP (Standard Temperature and Pressure), we'll follow these steps:

Given Data

Volume of the balloon, [tex]$ V = 20.0 $ L[/tex]

Pressure of the helium gas,[tex]$ P = 1.50 $ atm[/tex]

Temperature of the helium gas, [tex]$ T = 25.0 $ ^\circ C[/tex]

Convert Temperature to Kelvin

First, convert the temperature from Celsius to Kelvin:

[tex]\[ T_{\text{Kelvin}} = T_{\text{Celsius}} + 273.15 \][/tex]

[tex]\[ T_{\text{Kelvin}} = 25.0^\circ C} + 273.15 \][/tex]

[tex]\[ T_{\text{Kelvin}} = 298.15 \text{ K} \][/tex]

Calculate the Number of Moles (using the Ideal Gas Law)

The ideal gas law equation relates the pressure, volume, temperature, and number of moles [tex]($ n $)[/tex] of a gas:

[tex]\[ PV = nRT \][/tex]

where:

[tex]$ P $[/tex] is the pressure in atmospheres (atm)

[tex]$ V $[/tex] is the volume in liters ([tex]L[/tex])

[tex]$ n $[/tex] is the number of moles of gas

[tex]$ R $[/tex] is the ideal gas constant, [tex]$ R = 0.0821 $ L\ atm/mol\ K[/tex]

[tex]$ T $[/tex] is the temperature in Kelvin ([tex]K[/tex])

First, calculate [tex]$ n $[/tex] using the ideal gas law:

[tex]\[ n = \frac{PV}{RT} \][/tex]

Now, substitute the given values:

[tex]\[ n = \frac{(1.50 \text{ atm}) \times (20.0 \text{ L})}{(0.0821 \text{ L·atm/mol·K}) \times (298.15 \text{ K})} \][/tex]

[tex]\[ n = \frac{30.0 \text{ atm·L}}{24.485 \text{ L·atm/mol}} \][/tex]

[tex]\[ n = 1.225 \text{ mol} \][/tex]

How much heat is needed to change 5.42 grams of solid gold to liquid gold at its melting point of 1,063°C? The latent heat of fusion of gold is 66.6 J/g.

Answers

[tex]5.42 \times 66.6 = 360.972[/tex]
360.972 J

Answer:

360.97 J

Explanation:

mass of gold, m = 5.42 g

Latent heat of fusion, L = 66.6 J/g

The amount of heat required to convert 1 kg of solid into liquid state at its melting point is called latent heat.

L = Heat / mass

So, L = Q / m

Q = m L

Where, Q is the amount of heat supplied and L be latent heat of fusion amd m be the mass of substance.

Q = 5.42 x 66.6

Q = 360.97 J

Thus, the amount of heat required to melt the desired amount of gold is 360.97 J.

If the diameter of the black marble is 3.0 cm, and by using the formula for volume, what is a good approximation of its volume? Record to the ones place.
______cm3
Determine the initial volume of water in the graduated cylinder. If you added the black marble to the graduated cylinder and it sinks, what final volume should the water level indicate? Record to the ones place.
______ML

Answers

Answer:

The answers are 14 and 124, respectively.

Explanation:

The proof for these answers is the image attached.

Answer:

it is 14 and 124 I have took the test.

Explanation:

The two balls are an "action-reaction" pair. Ball 2 had a reaction to the action of ball 1, but ball 1 also had a reaction to ball 2. Explain how each ball moved after the collision in terms of the forces the balls exerted on each other.

Answers

Newton’s first law I guess

The specific heat of gold is 0.126 J/g°C. What mass of gold would change its temperature from 25.0 °C to 60.0 °C with the addition of 2825 J of heat energy? a 570 g b 641 g c 540 g d 610 g

Answers

The amount of heat energy needed to increase the temperature of a substance by [tex]\Delta T[/tex] is given by:
[tex]Q=m C_s \Delta T[/tex]
where m is the mass of the substance, Cs is its specific heat capacity and [tex]\Delta T[/tex] is the increase in temperature of the substance.

In this problem, we have a certain mass m of gold, with specific heat capacity [tex]C_s=0.126 J/g^{\circ}C[/tex], to which we add Q=2825 J of energy. Its temperature increases by [tex]\Delta T=60-25=35 ^{\circ}C[/tex]. Therefore, if we re-arrange the previous equation, we can find the mass of the block of gold:
[tex]m= \frac{Q}{C_s \Delta T} = \frac{2825J}{0.126\cdot 35}} =641 g[/tex]
So, the correct answer is B.

Answer:

The correct answer is option B, 641 g

Explanation:

The mass of a full bottle of cooking oil is 1.30 kg when half Is empty calculate mass of empty bottle

Answers

Mass of bottle + cooking oil = 1.3 kg
Mass of bottle + 1/2 cooking oil = 0.9 kg
Thus half cooking oil = 1.3 - 0.9
= 0.4 kg
Mass of cooking oil in a full bottle = 0.4 × 2
= 0.8 kg
Therefore the mass of the empty bottle
= 1.3 - 0.8
= 0.5 kg

What term describes an energy resource that can be used up?

Answers

Answer:
non-renewable energy resources are the ones that can be used up

Explanation:
Energy resources can be classified into two categories:
1- non renewable resources: these are the energy resources that cannot renew themselves. They are the resources that are formed from sources that can be consumed and run out. All fossil fuels are considered non renewable resources
Examples of non renewable energy resources: coal, oil, gas, petroleum , ......

2- renewable resources: these are the energy resources that are always present and can easily be renewed. Therefore, they do not come to an end.
Examples of renewable resources: solar energy, wind energy,.....

Based on the above, the energy resource that can be used up is the non renewable energy resource.

Hope this helps :)

Answer:

Non-renewable resource

Explanation:

There are two types energy resources.

1. Renewable resource: The resource of energy which is present in abundant quantity and replenishes itself in nature.

For example: solar energy, wind energy etc.

2. Non-renewable- The resource of energy which is present in limited quantity and does it takes millions of years to replenish. It can be used up. For example: Coal, oil and gas.

Which are ways of showing probability? Check all that apply.

Answers

i would say

-50%

-3/4

-25%

-7/8

Answer: a c e f

Explanation:

How much time does it take to use 300 W of power to do 1800 J of work? Round your answer to the nearest whole number. The time is s.

Answers

Energy = power × time
1800 = 300 × time
time = 1800 ÷ 300 = 6 s

Hope it helped!

Answer:

It takes 6 seconds

Explanation:

Power is the rate of doing work. Power used or dissipated can be calculated as the relationship between the work done and the time it took to do it. That's why its units are also J/s.

Mathematically:

[tex]Power=\frac{Work}{time}[/tex]

In this case, we know about the Power and the work done, so we can calculate the time it took. Solving for time:

[tex]time=\frac{Work}{Power}[/tex]

Plugging in the values:

[tex]time=\frac{1800J}{300J/s}\\time=6s[/tex]

A driver in front of you is signaling with his or her hand and arm pointing upward this driver wants to

Answers

Go straight. The man wants to go straight on the road.

help me plzzzz i will give u a medal
Which statement best describes how light waves travel in a uniform medium?

A.
in straight lines

B.
in extending circles

C.
in bent lines

D.
in shrinking ripples,

Answers

Option A. In straight lines. In a uniform medium, the light waves travel in a straight line through a vacuum. These waves vary in lengths through a vacuum consisting of periodic oscillations of electric and magnetic fields that cause the particles that traverse the lines in the vacuum.

The answer is in straight lines

When you look into a clear pond, a fish may appear to be in a different position than it actually is. What is this caused by?

A. diffraction

B. dispersion

C. refraction

D. reflection,

Answers

Refraction Refraction is when waves are deflected when passing obliquely through the interface between one medium and another or through a medium of varying density. (the pond water)

How does the mass relate to the momentum ?

Answers

Hi there!

Mass relates to momentum because
the heavier the object is, the more energy ît takes to make it start moving and make it stop. For example, if I had a 20 pound object and a 50 pound object, the 50 pound object would travel less than the 20 pound object when the same amount of force is exerted on it.

Hope this helps!

PLEASE HELP ASAP :|

In a complete sentence using all keywords below, describe how you can charge a balloon and have it stick to the wall?

Keywords: wool/felt/hair,, balloon, electrons, wall, negative charge, and positive charge.

Make sure to use all keywords correctly for 6 points.

Answers

Rub a balloon on a woolen fabric to pick up some electrons, to make the balloon negatively charged, and stick them to a wall, which would be positively charged to make them stick.

Opposites attract and when you stick a negatively charged objects to positively charged objects, they tend to stick together. When you pick up electrons, it increases the number of electrons which will make the object negatively charged.

Note: The first part of the answer is a single sentence. The problem says in a complete sentence, so just in case that you need only one sentence you can take the first part. If you can add in more than a sentence, you can put in more from the second paragraph.

what is the spring constant of a bungee cord that stretches an additional 28m when 300 n of force are applied

Answers

The magnitude of the force applied to the spring is equal to (Hook's law)
[tex]F=kx[/tex]
where k is the constant of the spring and x is the displacement of the spring with respect to its relaxed position.
In the exercise, the force applied is F=300 N while the displacement is x=28 m. Therefore the spring's constant is
[tex]k= \frac{F}{x}= \frac{300 N}{28 m}=10.7 N/m [/tex]

A strong magnetic field surrounds earth. How does earths magnetic feild help humans?

Answers

Answer:

Earth's magnetic field deviates high energy particles (e.g cosmic rays) that are a risk for human health.

Explanation:

Cosmic rays are high energy charged particles (88% protons, 10% nuclei of helium, 1% heavier nuclei) that came from the outer space. The energies of these particles are in the range of 1 GeV to 10⁸ TeV. Since they are charged particles, they will be deviated by Earth’s magnetic field¹ (as a reminder: A magnetic field applies a magnetic force over a moving charged particle).

Earth’s magnetic field works as a shield to humans against high energy charged particles, if cosmic rays were in touch with a human body, it can break molecules that forms DNA structure². Modifying that structure can lead to diseases as cancer, for example.

Units:

GeV: Giga-electronvolt

TeV: Tera-electronvolt

¹Magnetic field: It is generated around the space of a moving charged particle.

²DNA structure: It is a compound of different molecules that provides information to cells functionality.

What type of machine is a wire cutter pliers?

A.
simple machine

B.
compound machine,

Answers

Wire cutters are a compound machine, because there is more than one simple machine within them. There are two levels that are used as handles and two wedges that are used as blades. There is also another level in which takes its form as a rotating attachment point.

Answer:

took quiz other pearson right

Explanation:

A very small object with mass 6.90 × 10^−9 kg and positive charge 8.30 × 10^−9 C is projected directly toward a very large insulating sheet of positive charge that has uniform surface charge density 5.90 x 10^-8 C/m^2. The object is initially 0.530 m from the sheet.

What initial speed must the object have in order for its closest distance of approach to the sheet to be 0.170 m ?,

Answers

Mass of the object m = 6.90 × 10^−9 kg Charge of the object Q = 8.30 × 10^−9 C Surface charge density = 5.90 x 10^-8 C/m^2 Distance d1 = 0.530 m, d2 = 0.170 m Kinetic energy KE = 1/2 mv^2 Work = F x d = electric field x q x d => E x 8.30 × 10^−9 x (0.530 - 0.170) Following the energy conversion principles, 1/2 x 6.90 × 10^−9 x v^2 = E x 8.30 × 10^−9 x (0.530 - 0.170) 3.45 x v^2 = 8.30 x 0.36 x E => 3.45v^2 = 3E calculating the electric field E = 5.90 x 10^-8 / ( 2 x 8.85 x 10^-12) = 3333 So 3.45v^2 = 3 x 3333 => v^2 = 9999 / 3.45 => v^2 = 2898 => v = 53.8 m/s Intial speed v = 53.8 m/s

Which of the following items is most sensitive to increased acidity in the environment?

Answers

concrete buildings. i hope this helps you

Answer: CONCRETE BUILDINGS

Explanation:

i got it right in my quiz

Select all that apply. A hypothesis is _____. always correct determined before experimentation begins the experimental factor that changes in response to a change in the independent variable testable and falsifiable

Answers

Final answer:

A hypothesis is a testable and falsifiable assumption known before experimentation. It's not always correct and does not always change in response to a change in the independent variable. Even when experiments support a hypothesis, it is not confirmed as absolutely correct.

Explanation:

A hypothesis is a testable and falsifiable assumption based on what is known. It is determined before any experiment begins and serves as a guide for the collection and analysis of data. For instance, we could formulate a hypothesis like, 'If I water plants with sugar-mixed water, they will grow faster.'. If subsequent experimentation disproves this hypothesis, it must be discarded or reformed.

A hypothesis does not necessarily change in response to a change in the independent variable; rather, it predicts the expected response or outcome. However, a hypothesis is not always correct. It represents our best prediction based on the current information and can often be proven wrong as new data or insights become available via further empirical research.

Furthermore, in scientific research, even though a hypothesis is supported by multiple experiments, it does not confirm it to be correct, as future experiments could contradict it. Also, if a hypothesis explains a large amount of experimental data it could be considered a theory, but even theories can be modified if new data appears.

Learn more about Hypothesis here:

https://brainly.com/question/39619836

#SPJ12

Gloria pushes a full shopping cart with a force of 16 N. The cart has a mass of 19 kg. As Gloria pushed on the cart, she increased its velocity by 8.0 m/s. For how long did Gloria apply the force to the shopping cart?

Answers

Force on the cart = (cart's mass) x (cart's acceleration)

16 N = (19 kg) x (acceleration)

Acceleration of the cart = 16 N / 19 kg = 0.842 m/s²

How many seconds did it have to accelerate at the rate of 0.842 m/s²
in order to increase its speed by 8 m/s ?

(8 m/s) / (0.842 m/s²) = 9.5 seconds

Other Questions

You get a $5,000 180-day 11% consumer loan on May 18. You make a $2,000 payment on July 18. Calculate the balance you still owe after the payment. Assume a 365-day year. Which marketing metric measures the percentage of the target market that has been exposed to a promitonal message at least once during a specific time period? PLEASE HELP ASAP!! CORRECT ANSWER GETS BRAINLYEST!!Multiply. (2x+1)(x5) Express the answer in standard form. Enter your answer in the box How do institutions like religion and politics play a role in creating or maintaining beliefs and preconceived notions Which statement implies that some critics do not like H. Vondermoot's work? A)"Vondermoot creates another eerie masterpiece in Cryptic Inducement." B)"Perhaps the finest scene in the novel is the ending, which I wont ruin for you." C)"Vondermoot could have brought Cryptic Inducement down about 100 pages and still wowed his readers." D)"Some point out that Vondermoot still refuses to acknowledge that the Internet is shrinking the attention span of readers." TKAM Lee portrays Scout's formal schooling as rather hopelessly ineffective.TrueFalse Each chef at "sushi emperor" prepares 151515 regular rolls and 202020 vegetarian rolls daily. on tuesday, each customer ate 222 regular rolls and 333 vegetarian rolls. by the end of the day, 444 regular rolls and 111 vegetarian roll remained uneaten. how many chefs and how many customers were in "sushi emperor" on tuesday? Which of the following is the correct name for the compound MgBr2?Magnesium bromateMagnesium bromideMagnesium dibromideMagnesium (1) bromide Briefly explain the concept of steady state as it applies to diffusion. Why do rhyolite eruptions tend to produce large calderas? A chef cooked 8 kilograms of mashed potatoes for a dinner party.if the guests only ate 6/8 of the amount he cooked, how much did they eat? Do they still sell hand boards at dollar tree Can someone help me find the measure of angle C? What is the volume of a cube with a side length of 13 inches? A. 1014 in3 B. 169 in3 C. 2197 in3 D. 39 in3 You notice that heat is released during a chemical reaction. This reaction is a(n) _______ reaction. she term was muckcracker was used during the progressive moment to describe Degausser creates a magnetic field that erases data from magnetic storage media. a. True b. False How did early cyanobacteria affect the physical and chemical conditions on earth? what is equivalent to 3/5-5/6=-7/30 PLEASE HELP ME!!! ONLY 1 QUESTION!!! ILL GIVE YOU A MEDAL AND FAN YOU!! PLEASE!!Act 4 scene 2 Romeo And Juliet: capulet: so many guests invite as here are writ.-- Sirrah, go hire me twenty cunning cooks. second Servant: you shall have none ill, sir; for ill try if they can lick their fingers. Capulet: How canst thou try them so?Second Servant: Marry sir, 'tis and ill cook that cannot lick his own fingers: therefore he that cannot lick his fingers goes not with me. HOW DOES SHAKESPEARE'S USE OF COMIC RELIEF IMPACT T THIS SCENE?,