Why do we use the two-body problem to solve interplanetary trajectories, instead of including all of the appropriate gravitational forces that actually apply?

Answer:

3. Is 180◦ out of phase with the original wave at the end.

Explanation:

Here when wave is reflected by the rigid boundary then due to the rigidly bounded particles at the end or boundary they have tendency not to move and remains fixed at their position.

Due to this fixed position we can say when wave reach at that end the particles will not move and they apply equal and opposite force at the particles of string

Due to this the reflected wave is transferred back into the string in opposite phase with respect to the initial wave

so here correct answer will be

3. Is 180◦ out of phase with the original wave at the end.

Answer:

[tex]E' = \frac{E}{8}[/tex]

Explanation:

As we know that that electric field inside the solid non conducting sphere is given as

[tex]\int E.dA = \frac{q_{en}}{\epsilon_0}[/tex]

[tex]\int E.dA = \frac{\frac{Q}{R^3}r_1^3}{\epsilon_0}[/tex]

[tex]E(4\pi r_1^2) = \frac{Qr_1^3}{R^3 \epsilon_0}[/tex]

so electric field is given as

[tex]E = \frac{Qr_1}{4\pi \epsilon_0 R^3}[/tex]

now if another sphere has same charge but twice of radius then the electric field at same position is given as

[tex]E' = \frac{Qr_1}{4\pi \epsilon_0 (2R)^3}[/tex]

so here we have

[tex]E' = \frac{E}{8}[/tex]

Final answer:

The electric field at distance r1 from the center of a uniformly charged sphere with charge Q and radius 2R would be one-eighth of the field when the charge is within a sphere with radius R.

Explanation:

To find the electric field at a distance r1 from the center of a uniformly charged sphere, we can use Gauss's law. Inside a uniformly charged sphere, the electric field is proportional to the distance from the center because only the charge enclosed by a Gaussian surface contributes to the field at a point. The field inside the sphere can be described using the formula E = (Qr) / (4πε₀R³), where Q is the total charge, r is the distance from the center, R is the radius of the sphere, and ε0 is the permittivity of free space.

When the same total charge Q is distributed uniformly throughout a sphere of radius 2R, for a point at a distance r1 inside the sphere, which is still less than 2R, the electric field magnitude would be calculated with the new radius. Since the enclosed charge within the distance r1 would be the same and the volume of the larger sphere is greater, the electric field at r1 would be one-eighth of its original value, due to the volume of the sphere increasing by eight times when the radius is doubled (since the volume is proportional to the cube of the radius). Therefore, the new electric field magnitude at distance r1 would be E/8.

Answer:

8.6 J

Explanation:

Work done by the block = change in energy in the spring

W = ½ kx²

W = ½ (254.0 N/m) (0.26 m)²

W = 8.6 J

Answer: (a) 0.3679

(b) 0.0803

Explanation:

Given : A book of 600 pages contains 600 such errors.

Then , the average  number of errors per page = [tex]\dfrac{600}{600}=1[/tex]

[tex]\text{i.e. }\lambda=1[/tex]

The Poisson distribution function is given by :-

[tex]P(x)=\dfrac{e^{-\lambda}\lambda^x}{x!}[/tex]

Then , the probability that that page 1 contains no errors ( Put [tex]x=0[/tex] and [tex]\lambda=1[/tex]) :-

[tex]P(x=0)=\dfrac{e^{-1}1^0}{0!}=0.3678794411\approx0.3679[/tex]

Now, the probability that page 1 contains at least three errors :-

[tex]P(x\geq3)=1-(P(0)+P(1)+P(2))\\\\=1-(\dfrac{e^{-1}1^0}{0!}+\dfrac{e^{-1}1^1}{1!}+\dfrac{e^{-1}1^2}{2!})=0.0803013970714\approx0.0803[/tex]

Answer:

should be the answer B

Explanation:

Answer:

4.2 m/s²

Explanation:

m = combined mass of car and driver = 869 kg

a = maximum acceleration reached by the car with driver in it = 5.6 m/s²

Force provided by the engine is given as

[tex]F_{eng}[/tex] = ma

[tex]F_{eng}[/tex] = (869) (5.6)

[tex]F_{eng}[/tex] = 4866.4 N

M = Combined mass of car, driver and his three friends = 869 + 300 = 1169 kg

a' = maximum acceleration reached with friends in the car = ?

Force provided by the engine remains same and is then given as

[tex]F_{eng}[/tex] = M a'

4866.4 = (1169) a'

a' = 4.2 m/s²

Answer:

Electric force, [tex]F=2.88\times 10^{-14}\ N[/tex]

Explanation:

It is given that,

Magnitude of electric field, [tex]E=6\times 10^4\ N/C[/tex]

Charge, [tex]q=4.8\times 10^{-19}\ C[/tex]

The electric field is directed parallel to the positive y axis. We need to find the  force on the charge particle. It is given by :

[tex]F=q\times E[/tex]

[tex]F=4.8\times 10^{-19}\ C\times 6\times 10^4\ N/C[/tex]

[tex]F=2.88\times 10^{-14}\ N[/tex]

So, the electric force on the charge is [tex]2.88\times 10^{-14}\ N[/tex]. Hence, this is the required solution.

To calculate the potential difference VA - VB, first determine the displacement from point A to B. This results in a vector, which you dot product with the electric field vector to find the work done. This work done is the potential difference.

To compute the potential difference VA - VB, we first need to determine the displacement from point A to point B. This is determined by subtracting the coordinates of point A from point B, so (5 - 2)i + (7 - 3)j = 3i + 4j (meters). The next step involves calculating the work done by the electric field in moving a unit positive charge from A to B, which is obtained by taking the dot product of the displacement and the electric field vectors. Hence, the work done is (3i + 4j) . (4i + 3j) = 24 Joules/Coulomb. Now, since potential difference is defined as the work done per unit charge in moving a positive charge from one point to another, the potential difference VA - VB in this case would just be equal to this work done. So VA - VB = 24 Volts.

https://brainly.com/question/23716417

#SPJ3

Answer:

a) P = 44850 N

b) [tex]\delta l =0.254\ mm[/tex]

Explanation:

Given:

Cross-section area of the specimen, A = 130 mm² = 0.00013 m²

stress, σ = 345 MPa = 345 × 10⁶ Pa

Modulus of elasticity, E = 103 GPa = 103 × 10⁹ Pa

Initial length, L = 76 mm = 0.076 m

a) The stress is given as:

[tex]\sigma=\frac{\textup{Load}}{\textup{Area}}[/tex]

on substituting the values, we get

[tex]345\times10^6=\frac{\textup{Load}}{0.00013}[/tex]

or

Load, P = 44850 N

Hence the maximum load that can be applied is 44850 N = 44.85 KN

b)The deformation ([tex]\delta l[/tex]) due to an axial load is given as:

[tex]\delta l =\frac{PL}{AE}[/tex]

on substituting the values, we get

[tex]\delta l =\frac{44850\times0.076}{0.00013\times103\times 10^9}[/tex]

or

[tex]\delta l =0.254\ mm[/tex]

The maximum load that may be applied to the specimen without causing plastic deformation is 44850 N. The maximum length to which the specimen can be stretched without causing plastic deformation is 76.254 mm.

To find the maximum load that may be applied to the specimen without causing plastic deformation, we need to calculate the stress.

Stress = Force / Area

Where the force can be calculated by multiplying the stress with the cross-sectional area of the specimen.

Hence, maximum load = Stress × Area = 345 MPa × 130 mm² = 44850 N

To find the maximum length to which the specimen can be stretched without causing plastic deformation, we need to calculate the strain.

Strain = Change in length / Original length

Maximum length = Original length + (Strain × Original length) = 76 mm + (345 MPa / 103 GPa × 76 mm) = 76 mm + 0.254 mm = 76.254 mm

https://brainly.com/question/13261407

#SPJ3

Answer:

The pressure at constant velocity is 1.1 psi.

(1). is correct option.

Explanation:

Given that,

Diameter = 8 inch = 20.32 cm = 0.2032 m

Flow rate =2000 g/m

We need to calculate the velocity

[tex]v = \dfrac{Flow\ rate}{Area}[/tex]

[tex]2000\ g/m=\dfrac{0.00378\times2000}{60}[/tex]

[tex]2000\ g/m=0.1262 m^3/s[/tex]

[tex]v=\dfrac{0.1262}{\pi (0.1016)^2}[/tex]

[tex]v=3.89\ m/s[/tex]

We need to calculate the pressure

Using formula of pressure

[tex]P = \dfrac{1}{2}\rho v^2[/tex]

[tex]P=\dfrac{1}{2}\times1000\times(3.89)^2[/tex]

[tex]P=7566\ Pa[/tex]

[tex]P=1.09\ psi=1.1\ psi[/tex]

Hence, The pressure at constant velocity is 1.1 psi.

Answer:

a)

3.25 x 10⁵ m/s

b)

8.7 x 10²⁰ N

Explanation:

(a)

w = angular speed of the star = 1.8 x 10⁻¹⁵ rad/s

r = radius of the orbit = 1.9 x 10⁴ ly =  1.9 x 10⁴ (9.5 x 10¹⁵) m = 18.05 x 10¹⁹ m

tangential speed of the star is given as

v = r w

v = (18.05 x 10¹⁹) (1.8 x 10⁻¹⁵)

v = 32.5 x 10⁴ m/s

v = 3.25 x 10⁵ m/s

b)

m = mass of the star = 1.48 x 10³⁰ kg

Net force on the star to keep it moving is given as

F = m r w²

F = (1.48 x 10³⁰) (18.05 x 10¹⁹) (1.8 x 10⁻¹⁵)²

F = 8.7 x 10²⁰ N

(a) The height is [tex]h = 11.66\ m[/tex]. (b) If the speed is greater, the time required will be longer.

The height can be computed from the second equation of motion. However, for height to be computed, time is required. Therefore, the required time can be computed from distance and speed.

Given:

Horizontal velocity, [tex]u = 3.5 m/s\\[/tex]

Horizontal distance, [tex]x = 5.4 m/s\\[/tex]

(a)

The time is computed as:

[tex]t = x/u\\t = 5.4/3/5\\t = 1.5428/ s[/tex]

The height is given as:

[tex]h = 1/2gt^2\\h = 1/2 \times9.8\times1.5428^2\\h = 11.66\ m[/tex]

Hence, the height is [tex]h = 11.66\ m[/tex].

(b)

The relation between time and velocity is given as:

[tex]t= x/u\\t \alpha1/u[/tex]

The time and speed are inversely proportional. Therefore, if the velocity is larger then the time will be shorter.

Hence, if the speed is greater, the time required will be longer.

To learn more about Speed, here:

https://brainly.com/question/28224010

#SPJ12

Final answer:

To find the maximum height, we need to use the initial velocity and the angle of the baseball's trajectory. By breaking down the initial velocity into its horizontal and vertical components, we can then use the equation h = v_y^2 / (2g) to find the maximum height.

Explanation:

To find the maximum height, we first need to break down the initial velocity into its horizontal and vertical components. The initial velocity of the baseball is given as 100 ft/s at an angle of 45° with respect to the ground.

The horizontal component of velocity can be found using the equation: vx = v * cos(θ), where v is the initial velocity and θ is the angle.

The vertical component of velocity can be found using the equation: vy = v * sin(θ).

Once we have the vertical component of velocity, we can use the equation h = vy2 / (2g) to find the maximum height.
Substituting the given values, we have:
h = (100 * sin(45°))2 / (2 * 32)

Calculating this will give us the maximum height of the baseball above its initial position.

Answer:

1.25 m/s^2

Explanation:

m = 76 kg, R = 840 N

Let a be the acceleration of teh elevator in upward direction.

By use of Newton's second law

R - mg = m a

R = m ( g + a)

840 = 76 ( 9.8 + a)

a = 1.25 m/s^2

The acceleration of the elevator is [tex]\( {1.25 \, \text{m/s}^2} \)[/tex] upward.

Given:

- Mass of the man (m): 76 kg

- Weight of the man (W): mg where g is the acceleration due to gravity [tex](\( 9.8 \, \text{m/s}^2 \))[/tex]

- Normal force (read by the scale): 840 N (this includes the weight of the man plus any additional force due to acceleration)

The forces acting on the man in the elevator are:

- Downward force (weight of the man): ( mg )

- Upward normal force (read by the scale): [tex]\( 840 \, \text{N} \)[/tex]

The net force acting on the man is:

[tex]\[ F_{\text{net}} = \text{Normal force} - \text{Weight} \][/tex]

Since the elevator is accelerating upward with acceleration a, we have:

[tex]\[ F_{\text{net}} = m(g + a) \][/tex]

Given that the normal force read by the scale is 840 N, we equate it to [tex]\( m(g + a) \)[/tex]:

[tex]\[ 840 = 76 \times (9.8 + a) \][/tex]

Now, solve for a:

[tex]\[ 840 = 76 \times 9.8 + 76a \]\[ 840 = 744.8 + 76a \]\[ 76a = 840 - 744.8 \]\[ 76a = 95.2 \]\[ a = \frac{95.2}{76} \]\[ a \approx 1.25 \, \text{m/s}^2 \][/tex]

Answer:

Part a)

55.3 cm

Part b)

41.5 cm

Explanation:

Pipe A is open at both ends so the fundamental frequency of this pipe is given as

[tex]f_o = \frac{V}{2L}[/tex]

here we know that

V = 343 m/s

[tex]f_o = 310 Hz[/tex]

now we have

[tex]310 = \frac{343}{2L}[/tex]

[tex]L = 55.3 cm[/tex]

Now we also know that second harmonic of pipe A and third harmonic of pipe B has same frequency

so we will have

[tex]\frac{2V}{2L_a} = \frac{3V}{4L_b}[/tex]

[tex]L_b = \frac{3}{4}L_a[/tex]

[tex]L_b = \frac{3}{4}(55.3) = 41.5 cm[/tex]

Answer:

Part a)

i = 0

Part b)

i = 1 A

Explanation:

Part a)

As per Lenz law we know that inductor in series circuit opposes the sudden change in current

And if the flux in the circuit will change then it will induce back EMF to induce opposite current in it

Now when we close the switch at t = 0

then initially it will induce the opposite EMF in such a way that net EMF of the circuit will be ZERO

so current = 0

Part b)

After long time the induced EMF in the circuit will be zero as the flux will become constant

so here we can say

[tex]EMF = i(R_1 + R_2)[/tex]

[tex]12 = i (8 + 4)[/tex]

[tex]i = 1 A[/tex]

The initial current through the resistor in a series circuit with an inductor and resistor can be calculated using Ohm's Law. After a very long time, the current through the resistor becomes zero.

In a series circuit with an inductor and a resistor, the initial current through the resistor can be calculated using Ohm's Law. The total resistance in the circuit is the sum of the resistance of the inductor and the resistor. Using the formula I = V / R, where V is the voltage from the battery and R is the total resistance, we can calculate the initial current.

After a very long time, the inductor reaches a state of equilibrium with no change in current. So the current through the resistor a very long time after the switch is closed would be zero.

https://brainly.com/question/29554839

#SPJ11

The increase in force exerted on a diver's eardrum as they descend to a depth of 3.2m in a freshwater lake is due to the increased underwater pressure from the weight of the water above them. By calculating the pressure increase, and then multiplying this by the area of the eardrum, we find the increase in force is approximately 1.88 N.

The increase in pressure experienced by a diver as they go deeper underwater is due to the weight of the water above them; this weight results from the water's density, which is approximately 775 times greater than air. Hence, the force exerted increases with the increasing depth. To calculate the pressure increase, we use the formula: Pressure = fluid density * gravity * depth, and then the force on the eardrum is obtained by: Force = Pressure * Area.

In this case, the fluid density of freshwater is 1000 kg/m³, gravity is 9.81 m/s², the depth is 3.2 m, and the eardrum area is 0.60 cm² (or 0.00006 m² when converted to square meters).

So, the Pressure increase due to depth = 1000kg/m³ * 9.81m/s² * 3.2m = 31428 Pascal (or Pa); therefore, increase in force = 31428 Pa * 0.00006m² = 1.88 N, approximately. So, the increase in the force on the eardrum of the diver when she swims down to a depth of 3.2 m in the freshwater lake is around 1.88 Newtons.

https://brainly.com/question/6444848

#SPJ3

Final answer:

The increase in force pushing in on the eardrum at a depth of 3.2 m compared to the surface is 1.8816 N.

Explanation:

The student has asked about the increase in force on a diver's eardrum when diving to a depth of 3.2 m in a freshwater lake. The increase in force is due to the increase in water pressure with depth. To find the increase in the force on the eardrum, we need to calculate the water pressure at the depth of 3.2 m and multiply it by the area of the eardrum.

Water pressure increases by approximately 9.8 kPa per meter of depth (this is due to the weight of the water above). Therefore, at a depth of 3.2 m, the pressure is 3.2 m * 9.8 kPa/m = 31.36 kPa. The area of the eardrum is given as 0.60 cm², which is 0.60 * 10^-4 m² in SI units.

The increase in force F = pressure * area = 31.36 kPa * 0.60 * 10^-4 m². To get the force in newtons, we convert kPa to Pa by multiplying by 1,000, giving F = 31.36 * 1,000 Pa * 0.60 * 10^-4 m² = 1.8816 N.

The increase in force pushing in on the eardrum at a depth of 3.2 m compared to the surface is 1.8816 N.

Answer:

[tex]q_1 = 6.22 \times 10^{-11} C[/tex]

[tex]q_2 = -6.22 \times 10^{-11} [/tex]

Explanation:

Force on the charge Q = -1.85 mC is along the line joining the two charges

so here we can say that net force on it is given by

[tex]F = ma[/tex]

[tex]F = (0.00550)(314)[/tex]

[tex]F = 1.727 N[/tex]

Now this is the force due to two charges which are in same magnitude but opposite sign

so this force is given as

[tex]F = 2\frac{kq_1q}{r^2} cos\theta[/tex]

here we know that

[tex]F = 2\frac{(9\times 10^9)(1.85 \times 10^{-3})(q)}{0.03^2}cos\theta[/tex]

here we know that

[tex]cos\theta = \frac{2.25}{3} = 0.75[/tex]

now we have

[tex]1.727 = 2\frac{(9\times 10^9)(1.85 \times 10^{-3})(q)}{0.03^2}(0.75)[/tex]

[tex]1.727 = 2.775 \times 10^{10} q[/tex]

[tex]q = 6.22 \times 10^{-11} C[/tex]

Answer:

a) k  = 191.67 N\m

b) V = 22 m/s

c) t = 3.83s

d) 17.36m

e) 45.89 m

Explanation:

given:

F = 23 N

x = 12 cm = 0.12 m

mass of projectile, m = 5.7g = 5.7×10⁻³ kg

a) For a spring

F = kx

where,

F = Applied force

k = spring constant

x = change in in spring length

thus, we have

23 = k×0.12

or

k = 23/0.12

⇒ k  = 191.67 N\m

b) From the conservation of energy between the start and the point of interest we have

[tex]\frac{1}{2}\times kx^{2}=\frac{1}{2}mV^{2}[/tex]

where,

V = velocity of the projectile at 1.37 m above the floor

[tex]\frac{1}{2}\times 191.67\times 0.12^{2}=\frac{1}{2}5.7\times 10^{-3}V^{2}[/tex]

V = 22 m/s

c) time in air (t)

applying the Newtons's equaton of motion

[tex]h = Vsin\Theta\times  t +\frac{1}{2}a_{y}t^{2}[/tex]

substituting the values in the above equation we get

[tex]-1.37 = 22sin57^{\circ} \times  t +\frac{1}{2}(-9.8)t^{2}[/tex]

or

[tex]4.9t^{2}-18.45t-1.37 = 0[/tex]

solving the qudratic equation for 't', we get

t = 3.83s

d) For maximum height ([tex]H_{max}[/tex])

we have from the equations of projectile motion

[tex]H_{max} =\frac{V^{2}sin^{2}\theta }{2g}[/tex]

substituting the values in the above equation we get

[tex]H_{max} =\frac{22^{2}sin^{2}57^{\circ} }{2\times 9.8}[/tex]

or

[tex]H_{max} =17.36 m[/tex]

the height with respect to the ground surface will be = 17.36m + 1.37 m 18.73m

e)For horizontal distance traveled (R) we have the formula

[tex]R = Vcos\theta\times t[/tex]

substituting the values in the above equation we get

[tex]R =22\times cos57^{\circ} \times 3.83[/tex]

or

[tex]R =45.89 m[/tex]

Answer:

Explanation:

A unit vector is a vector whose magnitude is always unity that means 1 . It gives the direction of that quantity which is represented by this vector.

If the electric field is represented by a unit vector so it has same unit as electric field that means Newton per coulomb.

The unit of unit vector depend on the quantity for which it is used.

Final answer:

A unit vector is dimensionless and has no physical units, serving solely to represent direction in a vector space, such as the direction of an electric field.

Explanation:

In physics, particularly when discussing electric fields, the concept of vectors is crucial for understanding the direction and magnitude of forces. A unit vector is a standard tool used to simply indicate direction in space. Unlike other physical quantities, the unit vector is unique because it is dimensionless; that is, it has no units. This absence of units allows it to universally represent direction, irrespective of the nature of the physical quantity being described, such as an electric field.

When representing an electric field, which is a vector field, the direction in which a positive test charge would be pushed is shown by the unit vector. Vectors, as in the case of an electric field vector, are drawn as arrows with their length proportional to the magnitude and their orientation showing the direction. The unit vector associated with these fields provides direction but does not influence the physical units of the field itself, which are newtons per coulomb (N/C) for electric fields.

Answer:

a) Initial angular velocity of the turbine = 102.66 rad/s

b) Time elapsed while the turbine is speeding up = 157 s

Explanation:

a) Considering angular motion of turbine:-

Initial angular velocity, u =  ?

Acceleration , a = 0.155 rad/s²

Final angular velocity, v  = 127 rad/s  

Angular displacement, s = 2π x 2870 = 18032.74 rad

We have equation of motion v² = u² + 2as

Substituting

   v² = u² + 2as

    127² = u² + 2 x 0.155 x 18032.74

    u = 102.66 rad/s

Initial angular velocity of the turbine = 102.66 rad/s

b) We have equation of motion v = u + at

Initial angular velocity, u =  102.66 rad/s

Acceleration , a = 0.155 rad/s²

Final angular velocity, v  = 127 rad/s  

Substituting

  v = u + at

  127  = 102.66 + 0.155 x t = 157 s

Time elapsed while the turbine is speeding up = 157 s

Answer:

1.28 x 10^5 Pa

Explanation:

The absolute pressure at the bottom of the tank of water is given by:

[tex]p= p_0 + \rho g h[/tex]

where

[tex]p_0 = 1.03 \cdot 10^5 Pa[/tex] is the atmospheric pressure

[tex]\rho = 1000 kg/m^3[/tex] is the water density

g = 9.8 m/s^2 is the acceleration of gravity

h = 2.50 m is the heigth of the column of water

Substituting into the formula, we find

[tex]p=1.03\cdot 10^5 +(1000)(9.8)(2.50)=1.28\cdot 10^5 Pa[/tex]

Answer:

j

Explanation:

x = 4 t^2 - 2 t - 4.5

Position at t = 3 s

x = 4 (3)^2 - 2 (3) - 4.5 = 25.5 m

Velocity at t = 3 s

v = dx / dt = 8 t - 2

v ( t = 3 s) = 8 x 3 - 2 = 22 m/s

Acceleration at t = 3 s

a = dv / dt = 8

a ( t = 3 s ) = 8 m/s^2

When is the velocity = 0

v = 0

8 t - 2 = 0

t = 0.25 second

When is the position = 0

x = 0

4 t^2 - 2 t - 4.5 = 0

[tex]t = \frac{2 \pm \sqrt{4 + 72}}{8}[/tex]

t = 1.4 second

Final answer:

The minimum speed at which a car can travel around a curve without skidding is approximately 19.81 m/s.

Explanation:

To find the minimum speed at which a car can travel around a curve without skidding, we need to consider the forces acting on the car. The centripetal force required to keep the car moving in a circular path is given by the equation[tex]Fc = (mv^2)/r[/tex], where m is the mass of the car, v is the velocity, and r is the radius of the curve.

In this case, the centripetal force is provided by the friction force between the tires and the icy road. When the road is icy, the coefficient of static friction is approximately zero, so the car will not be able to rely on friction to round the curve. Instead, the car will rely on the component of the car's weight perpendicular to the road surface.

The perpendicular component of the weight is given by the equation Wp = mg * cos(θ), where m is the mass of the car, g is the acceleration due to gravity, and θ is the angle of banking of the curve.

Setting the centripetal force equal to the perpendicular component of the weight, we have[tex](mv^2)/r = mg * cos(\theta).[/tex]Rearranging the equation, we find v = sqrt(rg * cos(θ)). Substituting the given values of r = 40 m and θ = 0 (since there is no angle of banking), we can calculate the minimum speed as v = sqrt(40 * 9.81 * cos(0)) = sqrt(392.4) ≈ 19.81 m/s.

The shear deformation in a copper block due to applied forces can be calculated using the formula Δx = (F * L₀) / (S * A), where F is the force applied, L₀ is the initial length of the block, S is the shear modulus of copper, and A is the area of the surface on which the force is applied. The angle can then be calculated by taking the inverse tangent of the ratio of deformation (Δx) to the original length (L₀) of the block.

The subject of the question is related to the physics concept of shear strain and shear stress. The shear strain caused on a material, in this case copper, is defined by the sideways deformation of the material due to the applied force, and it is given by the formula Δx = (F * L₀) / (S * A). Here, F represents the force applied which is 3.07 X 10 6 N, L₀ is the height of the block which is 0.242 m. The shear modulus S of copper is given as 4.2 X 10¹⁰ N/m², and A is the area of the surface on which the force is applied, which can be calculated as 0.242 m² since a cube has all its sides equal. By substituting these values in the equation, we can calculate the value of the deformation Δx, which will give us an idea of how the shape of the block has been altered. The angle of shear can be obtained by taking the inverse tangent of the ratio of deformation to the original height of the cube.

https://brainly.com/question/12910262

#SPJ3

Answer:

Frequency, f = 0.274 Hz

Explanation:

It is given that,

Mass of the girl, m = 40 kg

Length of the rope, L = 3.3 m

We need to find the frequency of her swinging. It is an example of simple harmonic motion whose time period is given by :

[tex]T=2\pi\sqrt{\dfrac{L}{g}}[/tex]

[tex]T=2\pi\sqrt{\dfrac{3.3\ m}{9.8\ m/s^2}}[/tex]

T = 3.64 seconds

The frequency, [tex]f=\dfrac{1}{T}[/tex]

[tex]f=\dfrac{1}{3.64\ s}[/tex]

f = 0.274 Hz

So, the frequency of her swinging is 0.274 Hz. Hence, this is the required solution.

Answer:

31.3 m/s

Explanation:

The relation between the coefficient of friction and the velocity, radius of curve path is given by

μ = v^2 / r g

v^2 = μ r g

v^2 = 0.4 x 250 x 9.8 = 980

v = 31.3 m/s

Answer:

1184 kJ/kg

Explanation:

Given:

water pressure P= 28 bar

internal energy U= 988 kJ/kg

specific volume of water v= 0.121×10^-2 m^3/kg

Now from steam table at 28 bar pressure we can write

[tex]U= U_{f}= 987.6 kJ/Kg[/tex]

[tex]v_{f}=v=1.210\times 10^{-3}m^{^{3}}/kg[/tex]

therefore at saturated liquid we have specific enthalpy at 55 bar pressure.

that the specific enthalpy h =  h at 50 bar +(55-50)/(60-50)*( h at 50 bar - h at 60 bar)

[tex]h= 1154.5 + \frac{5}{10}\times(1213-1154)[/tex]

h= 1184 kJ/kg

Answer:

The ball covered the distance in 2 second is 20 m.

(b) is correct option.

Explanation:

Given that,

Time = 2 sec

Using equation of motion

[tex]s = ut+\dfrac{1}{2}gt^2[/tex]

Where, s = height

u = initial velocity

g = acceleration due to gravity

t = time

Put the value in the equation

[tex]s = 0+\dfrac{1}{2}\times9.8\times2^2[/tex]

[tex]s = 19.6\ approx\ 20\ m[/tex]

Hence, The ball covered the distance in 2 second is 20 m.

Answer:

Original speed of the mess kit = 4.43 m/s at 50.67° north of east.

Explanation:

Let north represent positive y axis and east represent positive x axis.

Here momentum is conserved.

Let the initial velocity be v.

Initial momentum = 4.4 x v = 4.4v

Velocity of 2.2 kg moving at 2.9 m/s, due north = 2.9 j m/s

Velocity of 2.2 kg moving at 6.8 m/s, 35° north of east = 6.9 ( cos 35i + sin35 j ) = 5.62 i + 3.96 j m/s

Final momentum = 2.2 x 2.9 j + 2.2 x (5.62 i + 3.96 j) = 12.364 i + 15.092 j kgm/s

We have

         Initial momentum = Final momentum

         4.4v = 12.364 i + 15.092 j

         v =2.81 i + 3.43 j

Magnitude

        [tex]v=\sqrt{2.81^2+3.43^2}=4.43m/s[/tex]

Direction

       [tex]\theta =tan^{-1}\left ( \frac{3.43}{2.81}\right )=50.67^0[/tex]

       50.67° north of east.

Original speed of the mess kit = 4.43 m/s at 50.67° north of east.