When two objects have the same momentum, the one with the smaller mass will have larger kinetic energy, because it must have a higher velocity. Conversely, if they have the same kinetic energy, the object with larger mass will have a higher momentum due to its larger mass.
Explanation:Understanding Momentum and Kinetic Energy.When considering two objects, one with a small mass and another with a large mass, that both have the same momentum, it's important to understand the relationship between momentum (p), mass (m), and velocity (v). Momentum is calculated as the product of mass and velocity (p = mv). To have the same momentum, a small mass must move with a larger velocity compared to a large mass.
When comparing kinetic energy (K), which is given by the formula K = (1/2)mv², the object with the smaller mass but higher velocity will have a larger kinetic energy. This is because kinetic energy is proportional to the square of velocity, and since the smaller mass has a higher velocity to maintain the same momentum, its kinetic energy will be greater. If the scenario is reversed and two objects have the same kinetic energy, then the large mass object must have a larger momentum. Since kinetic energy is the same, the larger mass object compensates for its lower velocity with its greater mass, leading to a greater momentum (p = mv).
A spring whose stiffness is 1140 n/m has a relaxed length of 0.51 m. if the length of the spring changes from 0.26 m to 0.79 m, what is the change in the potential energy of the spring? δu = -9.063 incorrect: your answer is incorrect. j
Final answer:
The change in potential energy of the spring is 152.19 J.
Explanation:
The potential energy of a spring is given by the equation PE = (1/2)kx², where k is the spring constant and x is the displacement of the spring. In this case, the change in length of the spring is 0.53 m (0.79 m - 0.26 m). We can calculate the potential energy change using the formula and given values:
PE = (1/2)(1140 N/m)(0.53 m)² = 152.19 J
Therefore, the change in potential energy of the spring is 152.19 J.
Photons of light with an energy of 656 nm are being directed through a chamber of hydrogen gas atoms. the gas atoms began in their ground state (ni=1). what happens?
Since there is not quite enough energy for transition from n=1 to n=2. So, the photons will pass through the gas chamber without affecting the gas.
Further explanation:
If the energy of photons is enough to excite all the electrons to go in higher state, the electron absorbs the energy of photon and go from a lower energy state to higher energy state. Transition of electron from lower energy state t higher energy state depends on the energy of photons.
Given:
The wavelength of the photons directed through a chamber of hydrogen gas atoms is [tex]656\text{ nm}[/tex].
The electron is excited from the energy state [tex]n=1[/tex] to higher energy state.
Concept:
The energy associated with a photon is given by the following relation.
[tex]E = \dfrac{{hc}}{\lambda}[/tex]
Here, [tex]E[/tex] is the energy associated with photon, [tex]h[/tex] is the plank constant, [tex]c[/tex] is the speed of the light and [tex]\lambda[/tex] is the wavelength associated with photon.
Substitute [tex]6.625\times{10^{-34}}\text{ J}\cdot\text{s}[/tex] for [tex]h[/tex], [tex]3.00\times{10^8}\text{ m/s}}[/tex] for [tex]c[/tex] and [tex]656\text{ nm}[/tex] for [tex]\lambda[/tex] in the above expression.
[tex]\begin{aligned}E&=\frac{{\left( {6.625 \times {{10}^{ - 34}}\,{\text{Js}}} \right)\left( {3.0 \times {{10}^8}\,{\text{m/s}}} \right)}}{{\left( {656 \times {{10}^{ - 9}}\,{\text{m}}} \right)}}\\&=3.0281 \times {10^{-19}}\,{\text{J}}\\\end{aligned}[/tex]
Rydberg equations is used to find out the energy level of an electron while transition from one energy state to another energy state.
[tex]\dfrac{1}{\lambda}=R{z^2}\left({\dfrac{1}{{n_1^2}}-\dfrac{1}{{n_2^2}}}\right)[/tex]
Here, [tex]\lambda[/tex] is the wavelength of the photons directed through a chamber, [tex]R[/tex] is the Rydberg constant, [tex]z[/tex] is the atomic number of hydrogen atom, [tex]{n_1}[/tex] is the lower energy state and [tex]{n_2}[/tex] is the higher energy state.
Substitute [tex]656\times{10^{-9}}\,{\text{m}}[/tex] for [tex]\lambda[/tex], [tex]1.0973 \times {10^7}\,{{\text{m}}^{{\text{-1}}}}[/tex] for [tex]R[/tex], [tex]1[/tex] for [tex]z[/tex] and [tex]1[/tex] for [tex]{n_1}[/tex] in the above expression.
[tex]\dfrac{1}{{\left( {656 \times {{10}^{ - 9}}\,{\text{m}}} \right)}} = \left( {1.0973 \times {{10}^7}{\mkern 1mu} {{\text{m}}^{{\text{-1}}}}} \right){\left( 1 \right)^2}\left( {\dfrac{1}{{{{\left( 1 \right)}^2}}}-\dfrac{1}{{n_2^2}}}\right)[/tex]
Simplify the above expression for [tex]{n_2}[/tex]
[tex]\begin{aligned}{n_2}&=\sqrt{\dfrac{1}{{0.861}}}\\&=1.08\\\end{aligned}[/tex]
From the above result it can be concluded that photons with wavelength [tex]656\text{ nm}[/tex] does not have enough energy to cause an electron to jump even one level higher.
Thus, there is not quite enough energy for transition from n=1 to n=2. So, the photons will pass through the gas chamber without affecting the gas.
Learn more:
1. A Na+ ion moves from inside a cell https://brainly.com/question/9251988
2. The kinetic energy of the emitted electrons when cesium is exposed to UV rays https://brainly.com/question/9059731
3. The frequency of the light for wavelength 7.1x10^2 nm https://brainly.com/question/9559140
Answer Details:
Grade: College
Subject: Physics
Chapter: Modern physics
Keywords:
Photons, light, energy, 656 nm, 656 times 10^-9 m, 6.56 times 10^-7 m, directed, chamber, hydrogen, gas atom, ground state, ni=1, 1.071, few, absorbed, quite enough, electrons, nf=2.
Final answer:
When photons with an energy of 656 nm pass through a chamber of hydrogen gas, the gas atoms can absorb these photons, causing the electrons to transition to higher energy levels.
Explanation:
When photons of light with an energy of 656 nm pass through a chamber of hydrogen gas atoms, the gas atoms can absorb photons that have the exact energy required to raise an electron from one energy level to another. In this case, the 656 nm photons have just the right energy to raise an electron in a hydrogen atom from the second to the third orbit.
When the hydrogen atoms absorb the 656 nm photons, the electrons that were initially in the second energy level will move to the third energy level, resulting in a number of missing photons of this wavelength and energy from the general stream of light passing through the gas. This phenomenon is known as absorption.
In summary, when photons with an energy of 656 nm pass through a chamber of hydrogen gas, the hydrogen gas atoms can absorb these photons, causing the electrons to transition to higher energy levels.
An object has a kinetic energy of 225 j and a momentum of magnitude 28.3 kg · m/s. (a) find the speed of the object. m/s (b) find the mass of the object
Jack is working with layer masks on an image, but he is worried that he may damage the image. Which of these would be an accurate fact about layer masks?
Layer masks are a non-destructive image editing technique that allows changes to be applied without altering the original image data, providing safety and flexibility in editing.
One accurate fact about layer masks in image editing is that they are non-destructive. This means that when Jack works with layer masks, he is not directly altering or damaging the original image data. Instead, layer masks allow him to apply changes, such as hiding or revealing parts of the layer, without permanently affecting the image. These masks can be edited at any time to adjust the visibility of different portions of the layer. If a mistake is made, Jack can simply edit the mask to correct the issue, rather than having to restore the original image from a separate file. Therefore, layer masks provide flexibility and safety for image editing, ensuring the original data remains intact.
Which scientists contributed to discovering the universal law of gravitation? Check all that apply. Tycho Brahe Albert Einstein Johannes Kepler Nicolaus Copernicus Sir Isaac Newton Robert Hooke
Tycho Brahe
Johannes Kepler
Nicolaus Copernicus
Sir Isaac Newton
Robert Hooke
The scientists contributed to discovering the universal law of gravitation are Tycho Brahe, Johannes Kepler , Nicolaus Copernicus , Sir Isaac Newton , and Robert Hooke .
What is science?Science is the methodical, empirically-based pursuit and application of knowledge and understanding of the natural and social worlds.
A method of learning about the world is science. Science allows people to participate in the creation of new knowledge as well as use that knowledge to further their goals.
Tycho Brahe, Johannes Kepler, Nicolaus Copernicus, Sir Isaac Newton, and Robert Hooke are the scientists who made significant contributions to the discovery of the gravitational constant.
Learn more about the science here , refer to the link given below :
https://brainly.com/question/18186842
#SPJ2
A wooden block has a mass of 986 g and a density of 16 g/ cm3. What is the volume?
A gas made up of atoms escapes through a pinhole 3.16 times as fast as ar gas. write the chemical formula of the gas.
Assuming the wind blew the same direction all night, what direction, in degrees north of west, did the wind blow jack during the night?
The question involves physics and vector subtraction to determine the wind's speed and direction affecting an airplane's travel based on its heading and ground velocity.
Explanation:The student is asking about determining the wind's speed and direction based on an airplane's velocity relative to the ground and its intended heading. To solve for this, we need to use vector subtraction since the airplane's ground velocity can be thought of as a combination of its own speed and the wind's influence. Given that the airplane is heading north at 45.0 m/s and its ground speed is 38.0 m/s at an angle west of north, the wind's speed and direction are the vectors that need to be added to the airplane's heading to equal the ground speed vector. A vector diagram would need to be drawn, and trigonometry would be used to calculate the magnitude of the wind's vector and its angle relative to the west.
With what speed must you approach a source of sound to observe a 25% change in frequency?
With the known value of v (speed of sound in the medium, e.g., 343 m/s) and the desired change in frequency (25% or 0.25), you can calculate the speed you must approach the source of sound to observe a 25% change in frequency.
To observe a 25% change in frequency (Doppler effect) when approaching a source of sound, you need to know the relative velocity between you and the source of sound. The Doppler effect occurs when there is relative motion between the observer and the source of the sound.
The formula for calculating the apparent frequency (f') observed by a moving observer due to the Doppler effect is:
f' = f * (v + vo) / (v - vs)
Where:
f' = Apparent frequency observed by the moving observer
f = Actual frequency of the sound emitted by the source
v = Speed of sound in the medium (approximately 343 meters per second in air at room temperature)
vo = Velocity of the observer (positive if moving towards the source, negative if moving away from it)
vs = Velocity of the source of sound (positive if moving away from the observer, negative if moving towards it)
Since want to observe a 25% change in frequency, the apparent frequency (f') would be 25% different from the actual frequency (f):
f' = 1.25 * f
Assuming the observer is moving towards the source (vo is positive), we can rewrite the equation as:
1.25 × f = f × (v + vo) / (v - vs)
Now, we can solve for the relative velocity vo:
(v + vo) / (v - vs) = 1.25
Cross-multiply:
v + vo = 1.25 * (v - vs)
Now, isolate vo:
vo = 1.25 × (v - vs) - v
With the known value of v (speed of sound in the medium, e.g., 343 m/s) and the desired change in frequency (25% or 0.25), you can calculate the speed you must approach the source of sound to observe a 25% change in frequency.
To know more about frequency
https://brainly.com/question/29739263
#SPJ2
what is rolling friction
Rolling friction is a force resisting motion when an object rolls on a surface. An example could be a ball rolling or a tire.
Which statement best describes how a wave would move differently through a pot of boiling water than the steam created from it? The wave would move faster through the water than through the steam. The wave would move slower through the water than through the steam. The wave would move the same speed through the water and the steam. The wave would move through the water and steam at the same speed, but decrease in speed at the transition point.
Answer:
The wave would move faster through the water than through the steam
Explanation:
A mechanical wave is a wave that is transmitted through the oscillations of the particles in a medium. The closer the particles in the medium are, the more efficient the transmission of the wave is (because the collisions between the particles are more frequent), and so the faster the wave.
For this reason, mechanical waves travel faster in liquids (such as water) than in gases (such as the steam): because particles in liquids are closer together than in gases, where they are more spread apart. Therefore, the correct choice is
The wave would move faster through the water than through the steam
A 2.00-kg metal object requires 1.00 × 104 J of heat to raise its temperature from 20.0 °C to 60.0 °C. What is the specific heat of the metal?
Answer:
0.125 J/(g·k)
Explanation:
Specific heat has units of J/(g·K), so we find the value by dividing the energy by the product of mass and temperature change.
(10^4 J)/(2·10^3 g·(60 -20)K) = 10/(2·40) J/(g·K) = 0.125 J/(g·k)
What is the fate of solar radiation that reaches the earth?
When solar radiation reaches the Earth, some parts of it is defused by the atmosphere and some parts transmitted to Earth's surface.
What is the solar radiation?A broad name for the electromagnetic radiation emitted by the sun is solar radiation, also known as the solar resource or just sunshine. With the use of various technologies, solar radiation may be absorbed and converted into usable forms of energy like heat and electricity. However, a certain location's solar resource determines whether these systems are technically feasible and operate economically.
Some of the sunlight is absorbed, scattered, and reflected by air molecules, water vapour, clouds, dust, pollutants, forest fires, and volcanoes as it travels through the atmosphere. The term for this is diffuse sun radiation.
Direct beam solar radiation is the type of solar radiation that directly reaches the surface of the Earth. Global solar radiation is the total of both diffuse and direct sun radiation. Direct beam radiation can be reduced by atmospheric conditions by 10% on clear, dry days and by 100% on days with heavy clouds.
Learn more about solar radiation here:
https://brainly.com/question/16525532
#SPJ5
A microwave oven operates at 2.70 ghz . what is the wavelength of the radiation produced by this appliance? express the wavelength numerically in nanometers.
The wavelength of the microwave radiation produced by microwave oven is [tex]\boxed{1.1\times {10^8}\,{\text{nm}}}[/tex].
Further Explanation:
A microwave is an appliance which is used to heat and cook food by direct exposing it to electromagnetic radiation. Microwave oven uses radio waves to heat and cook food. A magnetron is used as a source of microwave radiation.
The radiation travels with the speed of light inside the microwave oven.
Given:
The operational frequency of the microwave oven is [tex]2.70\text{ GHz}[/tex].
The speed of the radiation is [tex]3\times10^{8}\text{ m/s}[/tex].
Concept:
The frequency and wavelength of an electromagnetic radiation are related according to the following expression.
[tex]c=f \cdot \,\lambda[/tex]
Rearrange the above expression for [tex]\lambda[/tex] .
[tex]\boxed{\lambda=\dfrac{c}{f}}[/tex] …… (1)
Here, [tex]c[/tex] is the speed of light, [tex]f[/tex] is the frequency of the radiation and [tex]\lambda[/tex] is the wavelength of the radiation.
Converting [tex]\text{GHz}[/tex] into [tex]\text{Hz}[/tex].
[tex]2.70\,{\text{GHz=2}}{\text{.70}} \times {\text{1}}{{\text{0}}^9}\,{\text{Hz}}[/tex]
Substitute [tex]3.00 \times {10^8}\,{\text{m/s}}[/tex] for [tex]c[/tex] and [tex]2.70 \times {10^9}\,{\text{Hz}}[/tex] for [tex]f[/tex] in equation (1).
[tex]\begin{aligned}\lambda&=\frac{{3.00 \times {{10}^8}\,{\text{m/s}}}}{{2.70 \times {{10}^9}\,{\text{Hz}}}} \\&=0.11\,{\text{m}} \\&=1.1\times10^{8}\text{ nm} \\ \end{aligned}[/tex]
Thus, the wavelength of the microwave radiation produced by microwave oven is [tex]\boxed{1.1\times {10^8}\,{\text{nm}}}[/tex].
Learn more:
1. Rotational velocity https://brainly.com/question/2887706
2. Current through the inductor https://brainly.com/question/1695461
3. Force applied by car on truck https://brainly.com/question/2235246
Answer Details:
Grade: High school
Subject: Physics
Chapter: Electromagnetic radiation
Keywords:
Microwave oven, 2.70 GHz, 2.70 ghz, 2.70 times 10^9 Hz, wavelength, numerically, nanometers, 0.11 m, 0.11 times 10^9 nm, 1.1 times 10^8 nm , magnetron, 0.11 times 10power9 nm, 1.1 times 10 power 8 nm.
The wavelength of the radiation produced by the microwave oven is approximately 111,111,111 nanometers.
To find the wavelength of the radiation produced by a microwave oven operating at 2.70 GHz, you can use the formula:
Wavelength (λ) = Speed of Light (c) / Frequency (f)
Where:
Speed of Light (c) = 3 x [tex]10^8[/tex] meters per second (approximately)
Frequency (f) = 2.70 GHz = 2.70 x [tex]10^9[/tex] Hertz
Now, plug these values into the formula:
λ = (3 x [tex]10^8[/tex] m/s) / (2.70 x [tex]10^9[/tex] Hz)
λ = 0.1111 meters.
To express this wavelength in nanometers, you can convert meters to nanometers. There are 1 billion nanometers in a meter, so:
λ ≈ 0.1111 meters * 1,000,000,000 nanometers/meter ≈ 111,111,111.11 nanometers
Hence , The wavelength of the radiation produced by the microwave oven is approximately 111,111,111 nanometers.
To know more about wavelength here
https://brainly.com/question/4844737
#SPJ3
A 9.00-g bullet is fired horizontally into a 1.20-kg wooden block resting on a horizontal surface. the coefficient of kinetic friction between block and surface is 0.20. the bullet remains embedded in the block, which is observed to slide 0.340 m along the surface before stopping. part a what was the initial speed of the bullet? express your answer with the appropriate units.
To find the initial speed of the bullet, we can use the conservation of linear momentum. By applying the conservation of momentum equation, we can solve for the initial velocity of the bullet. In this case, the initial velocity of the bullet is found to be 0 m/s.
Explanation:To find the initial speed of the bullet, we need to consider the conservation of linear momentum. The initial momentum of the bullet is equal to the final momentum of the bullet and the block together.
The momentum of an object is given by the product of its mass and velocity. The bullet has a mass of 9.00 g and its velocity is the initial speed we want to find. The block has a mass of 1.20 kg and its velocity is 0 m/s initially.
Applying the conservation of momentum, we have: (mass of bullet) × (initial velocity of bullet) = (mass of bullet + mass of block) × (final velocity of bullet + block).
Since the bullet remains embedded in the block, the final velocity of the bullet and block together is 0 m/s. Plugging in the values, we can solve for the initial velocity of the bullet.
9.00 g × (initial velocity of bullet) = (9.00 g + 1.20 kg) × 0
(initial velocity of bullet) = 0 / (10.2 g)
(initial velocity of bullet) = 0 m/s
At the top of a giant swing on the gymnastics high bar, candy's velocity is 1 m/s, and she is 3.5 m high. if candy's mass is 50 kg, what is her total mechanical energy at this instant?
At the top of the giant swing on the gymnastics high bar, candy's total mechanical energy is 1740J.
Given the data in the question;
Candy's velocity; [tex]v = 1 m/s[/tex]Candy's height from the ground; [tex]h = 3.5m[/tex]Candy's mass; [tex]m = 50kg[/tex]Candy's total mechanical energy; [tex]M.E_c = \ ?[/tex]
Total Mechanical Energy (M.E) is the sum of both the potential energy and the kinetic energy of an object.
[tex]Mechanical \ Energy = Potential \ Energy + Kinetic \ Energy[/tex]
[tex]M.E = mgh + \frac{1}{2}mv^2[/tex]
Where m is the mass, g is gravitational acceleration( [tex]9.8m/s^2[/tex] ), h is the height and v is the velocity.
We substitute our values into the equation
[tex]M.E_c = ( 50kg * 9.8m/s^2*3.5m) + ( \frac{1}{2}* 50\ *(1m/s)^2)\\\\M.E_c = 1715kg.m^2/s^2 + 25kg.m^2/s^2\\\\M.E_c = 1740 kg.m^2/m^2\\\\M.E_c = 1740J\\[/tex]
Therefore, at the top of the giant swing on the gymnastics high bar, candy's total mechanical energy is 1740J
Learn more: https://brainly.com/question/5046985
Which of the following statements best describes the labor market in the field of healthcare?
Answer:
b
Explanation:
An example of a radioactive isotope is carbon-12. carbon-14. neon-20. neon-22.
Carbon-14 is an example of a radioactive isotope because this element can emit radioactivity.
What is Radioactivity?
Radioactivity is a property where an element can emit energy and atomic particles in a spontaneous manner.
What is isotope?Isotopes are two or more types of atoms that have the same atomic number and position in the periodic table, and that differ in nucleon numbers due to different numbers of neutrons in their nuclei.
To learn more about radioactivity here
https://brainly.com/question/1770619
#SPJ2
Consider a wire that has resistance r, length l and the cross-sectional area
a. the correct expression for the resistivity of that wire is:
Answer:
[tex]\rho = \frac{RA}{L}[/tex]
Explanation:
.As we know that the resistance of the wire is given as
[tex]R = \rho \frac{L}{A}[/tex]
here we know that
A = cross-sectional area
L = length
R = resistance of wire
now multiply both sides of above equation with Area
[tex]R A = \rho L[/tex]
now divide both sides with length of the wire
[tex]\rho = \frac{RA}{L}[/tex]
so above is the expression of resistivity of wire in terms of resistance, Area and length of the wire
A hydrogen electron returns from energy level n = 3 to n = 1 during electron transition. What will the spectral lines emitted by this electron look like under a spectroscope? dark line spectrum white light continuous spectrum bright line spectrum
Answer:
when electron jump from n=3 to n=1 then the photon coming out is of Lyman series. Here Lyman series photon is also known as Ultraviolet range of photon
Explanation:
As per Bohr's theory we know that when electron make transition from higher energy level to lower energy level then it emits photons of different energy range.
Here we know that when electron makes transition from any higher level to n=1 then it is ultraviolet range of photons.
While if electron makes transition from any higher energy range to n= 2 then it is visible range of photons
and for any higher energy level to n=3 then it is infrared range of photon
So here the spectrum received in this case is of ultraviolet range
Which layer of the sun is responsible for producing the light shown in the picture above?
Radiative zone
Convective zone
Photosphere
Chromosphere
Answer:
C. Photosphere
Explanation:
The lights shown in the figure comes from the outermost layer of the Sun. This layer is called photosphere.
This is the layer from where the light of the Sun is radiated, before travelling through space and reaching us.
The photosphere is the coldest layer of the Sun: its surface temperature is between 4500 and 6000 K. Its width is approximately 100 km.
A characteristic of the photosphere is the presence of the sunspots, which appear as darker spots, and are regions of lower temperature caused by a concentration of magnetic flux.
The correct option is Option C( Photosphere).The photosphere is the layer of the sun responsible for producing the visible light we see. It has a temperature range of 4500 K to 6800 K. The photosphere is the sun's visible surface.
The layer of the sun responsible for producing the light that we see is the photosphere. The photosphere is the visible surface of the sun and has a temperature that ranges from 4500 K to about 6800 K. It is where the light that we see directly is emitted. Above the photosphere are other layers such as the chromosphere and the corona, but it is the photosphere that generates the light."(a) how much charge can be placed on a capacitor with air between the plates before it breaks down if the area of each plate is 6.00 cm2? (assume air has a dielectric strength of 3.00 ✕ 106 v/m and dielectric constant of 1.00.)"
A block with mass 0.5kg is forced against a horizontal spring of negligible mass, compressing the spring a distance of 0.2m. when the spring is released, the block moves on a horizontal tabletop for 1.00 m before coming to rest. the force constant k is 100n/m. what is the coefficient of kinetic friction μk between the block and the tabletop?
Dario, a prep cook at an italian restaurant, spins a salad spinner and observes that it rotates 20.0 times in 5.00 seconds and then stops spinning it. the salad spinner rotates 6.00 more times before it comes to rest. assume that the spinner slows down with constant angular acceleration. part a what is the magnitude of the angular acceleration of the salad spinner as it slows down?
For an uniformly accelerated motion, the following relationship is used:
[tex]2 a S=v_f^2 -v_i ^2[/tex] (1)
where a is the acceleration, S the distance covered, and vf and vi the final and initial speeds of the motion.
In our problem we are dealing with a rotational motion. Initially, the salad spinner has constant angular speed, which is given by
[tex]\omega _i = 2 \pi f[/tex]
where f is the rotational frequency, which is the number of revolutions per second:
[tex]f= \frac{20 rev}{5 s}=4 Hz [/tex]
so the initial angular speed is
[tex]\omega _i = 2 \pi (4 Hz)=25.2 rad/s[/tex]
Then, the salad spinner starts to decelerate with constant deceleration [tex]\alpha[/tex], and during its deceleration it spins for other 6 revolutions, so covering a total angle of
[tex]\theta = 2 \pi (6 rev)=37.7 rad[/tex]
until it stops, so until it reaches a final speed of [tex]\omega _f=0[/tex].
To find the angular acceleration, we can use the equivalent of equation (1) for angular motions:
[tex]2 \alpha \theta = \omega_f^2 - \omega_i^2[/tex]
and so, since the final speed is [tex]\omega _f=0[/tex]:
[tex]\alpha = - \frac{\omega _i^2}{2 \theta}=- \frac{(25.2 rad/s)^2}{2\cdot 37.7 rad}=-8.4 rad/s^2 [/tex]
where the negative sign means the salad spinner is decelerating.
Answer:
[tex] \alpha = -\frac{(25.132 rad/s)^2}{2* 37.7 rad}= -8.377 rad/s^2[/tex]
And we can convert this into degrees like this:
[tex] \alpha= -8.377 rad/s^2 * (\frac{180}{\pi rad}) =-479.967 rad/s^2[/tex]
Explanation:
For this case we assume that the angular acceleration is constant and the spinner slows down and come to rest at the end
We can calculate the distance traveled each revolution with this formula:
[tex] \theta= 20 rev * \frac{2\pi rad}{1 rev}= 40 \pi rad[/tex]
And since we know that the time to reach the velocity 0 is 5 s we can find the angular velocity like this:
[tex] w_o= \frac{\theta}{t}= \frac{40 \pi rad}{5 s}= 25.132 rad/s[/tex]
We know that the spinner rotates 6 more times before come rest, so the total distance traveled is:
[tex] \theta= 6* 2\pi = 37.699 rad[/tex]
[tex] w_f = 0 rad/s[/tex]
And we have the following formula :
[tex] w^2_f = w^2_i + 2\alpha \theta[/tex]
Since we know that the final angular velocity is 0 we can solve for [tex] \alpha[/tex] the angular acceleration and we got:
[tex] \alpha = -\frac{w^2_o}{2 \theta}[/tex]
And replacing the values that we found before we have this:
[tex] \alpha = -\frac{(25.132 rad/s)^2}{2* 37.7 rad}= -8.377 rad/s^2[/tex]
And we can convert this into degrees like this:
[tex] \alpha= -8.377 rad/s^2 * (\frac{180}{\pi rad}) =-479.967 rad/s^2[/tex]
Describe a situation in which different units of measure could cause confusion.
Answer:
When different countries use different forms of measurement there is many different mistakes and confusion that can happen.
Explanation:
Final answer:
Different units of measure can cause confusion and serious mishaps in critical fields like medicine and aviation. Unit conversion is essential for clear communication, with dimensional analysis being a key tool for accurate conversions. Appropriate units must be used in context to avoid misunderstandings.
Explanation:
Different units of measure can lead to confusion, miscommunication, and even dangerous situations if not properly managed. This is particularly true in fields where precise measurements are critical, such as medicine, engineering, and aviation.
One famous example is the loss of the Mars Climate Orbiter spacecraft in 1999 due to the use of English units in the software while engineers used metric units for its development. Similarly, in 1983, an Air Canada plane ran out of fuel and had to make an emergency landing because the fuel tanks were filled using pounds instead of kilograms. Even in daily life, incorrect unit conversion can be problematic, such as when dispensing medication and precise dosages are required for safety.
To avoid such missteps, unit conversion is necessary. By converting units, we effectively communicate the same quantity in different terms. For example, 12 inches can also be expressed as 1 foot, but both units describe the identical length. Understanding dimensional analysis is key to accurate conversion and communication of measurements.
When selecting appropriate units, context is important to convey measurements accurately. The distance between two towns is best measured in kilometers or miles, the weight of a peanut in grams, the length of a hand in centimeters, and the volume of a raindrop in milliliters. Using the correct units ensures clarity and avoids confusion.
a system that uses reflected radio waves to detect objects and to measure their distance and speed is called
A monatomic ideal gas expands slowly to twice its original volume, doing 280 j of work in the process. find the heat added to the gas if the process is isothermal.
Express 4,560 m in km. Remember to keep the same number of significant figures in your answer as was in the original measurement.
Answer:
4.56 km.
Explanation:
Blessings.
Why does buying locally grown fruits and vegetables decrease your carbon footprint?
A.) They are grown without fertilizers.
B.) Less fuel is used to deliver these products to the market.
C.) They are healthier for you.
D.) Less water is used to grow these products.
What does it mean to say that science is a “systematic” process?