Answer:
Theres an unidentified puddle
Explanation:
That could mean that something is leaking
The presence of an unidentified puddle under or near the vehicle during a pre-drive check could indicate a potential fluid leak, and it is considered an abnormality that should be investigated for safety reasons.
Explanation:During your pre-drive check, the presence of another vehicle nearby, aligned mirrors, and a responsive steering wheel are all normal and necessary conditions for safe operation of a vehicle. However, d) there's an unidentified puddle under or near your vehicle may be an abnormality. This puddle could indicate a fluid leak such as oil, coolant, brake fluid, or transmission fluid, which can lead to mechanical failures and safety hazards while driving. It's crucial to investigate and identify any suspicious puddles before commencing a drive to ensure the roadworthiness of your vehicle.
If you're carrying a load that extends beyond the sides of your vehicle, you don't need to clearly mark it unless it extends more than _____ beyond the rear of the vehicle.
A. four inches
B. four feet
C. six feet
D. eight feet
Answer:
B. four feet
Explanation:
If you're carrying a load that extends beyond the sides of your vehicle, you don't need to clearly mark it unless it extends more than four feet beyond the rear of the vehicle.
Answer:b
Explanation: i did it and got it right
An engineer has been given a design challenge. The problem has been defined. Her team has brainstormed possible ideas. What should the team do next?
A. Communicate their ideas
B. Select a solution
C. Identify criteria
D. Research and develop ideas
Answer:
D. Research and develop ideas.
Explanation:
For any engineering idea that has been thought of, it should be well researched to evaluate its viability and possibilities. The ideas should be transformed into drawings and material lists.
The team should also explain how the ideas will work. Also it should explain how the ideas once implemented will be tested and evaluated.
If traffic is approaching on your left and there is a child riding a bike to your right, you should:
A. Move closer to oncoming traffic
B. Move closer to the bicyclist
C. Pull over until the road is clearer
Answer:
A. Move closer to oncoming traffic
Explanation:
If traffic is approaching on your left and there is a child riding a bike to your right, you should move closer to oncoming traffic.
Answer:
I believe the answer is C
Explanation:
Choosing option A would put you in danger. Choosing option B would put the child in danger. So your best bet would be to just pull over until all parties can continue safely.
When the piston is at its highest position in the cylinder, it’s said to be at _____________.
The _____________ is a hollow metal tube drilled into the metal engine block.
The top of the cylinder is sealed by a metal cover called the _____________.
In a gasoline-powered engine, the _____________ ignites the air-and-fuel mixture in the cylinder and causes it to burn.
Why is it critical for the upper and lower end sections of an engine to work perfectly together?
Answer:
1. top dead center (TDC)
2. cylinder
3. cylinder head
4. spark plug
5. Sample answer: It’s critical for both sections to work perfectly together because the process by which power is created occurs so quickly that the timing must be precise for an engine to run smoothly and safely.
Explanation:
penn foster
When the piston is at its highest position in the cylinder, it’s said to be at Top dead center
The Cylinder is a hollow metal tube drilled into the metal engine block.
The top of the cylinder is sealed by a metal cover called the Cylinder head.
The top of the cylinder is sealed by a metal cover called the Cylinder head
In a gasoline-powered engine, the spark ignites the air-and-fuel mixture in the cylinder and causes it to burn.
What covers the cylinder of its engine?In an internal combustion engine, the cylinder head (often abbreviated to simply "head") sits above the cylinders and forms the roof of the combustion chamber.
To learn more about the piston, refer
https://brainly.com/question/11506099
#SPJ2
What precautions should you take to prevent injuries when dealing with heavy loads?
Answer with explanation:
When dealing with heavy loads, one needs to take certain precautions in order to avoid or prevent from injuries.
For instance, one should avoid lifting above the shoulder level which can end up pulling your muscle.
Also, you can either break the load in parts if possible or get some help for lifting heavy bulks.
Moreover, one should try to lift with the legs while keeping the back straight and not twisting it.
Question 14(Multiple Choice Worth 3 points)
(Lesson 7.2 LC)
The daily driving limit for time spent behind the wheel should be no more than
O two hours
Otwo to four hours
O six to eight hours
O a maximum of 12 hours
Answer:
The daily driving limit for time spent behind the wheel should be no more than six to eight hours.- third choice
Answer:
C.
Explanation:
Tech A says never use a water hose to clean up dust after a repair. Tech B says never use a floor scrubber to clean up dust after repairs. Who is correct?
Answer:
Tech B
Explanation:
You ruin your mop that way. it will clump up and than you'll have a mud mess.
What is the lowest common denominator of 1/2 and 1/11
Answer:
22
Explanation:
2 and 11 are both prime so their GCF must be 2*11 which is 22.
For this case we have by definition, that the lowest common denominator of two or more fractions, is the number that results from calculating the lowest common multiple of the denominators of those same fractions.
We have the following fractions:
[tex]\frac {1} {2}[/tex] and[tex]\frac {1} {11}[/tex]
We look for the least common multiple of 2 and 11:
2: 2
11:11
[tex]l.c.m = 2 * 11 = 22[/tex]
Answer:
The lowest common denominator of the fractions is 22
3 MAOP stands for which of the following?
Maximum Allowable Operating Pressure
A home electrical system is joined to the electric company's system at the junction of the
A. neutral strip in the panelboard.
B. black and red wires in the meter.
C. panelboard and service drop.
D. service entrance head and service drop.
That would be B, I hope this helps!
A. suspended
B. denied
C. canceled
D. revoked
Answer:
D. revoked or A. suspended
(i would go with A.)
Explanation:
Highway racing is classified as a criminal misdemeanor offense, which carries a mandatory license revocation for one year , and could put you in jail for up to one year if you are convicted.
Speed limit signs are classified as
A. Mandatory signs
B. Regulatory signs
C. Warning signs
D. Traffic flow signs
Answer:
B. Regulatory signs
Explanation:
traffic rules
Your driver license will be _____ if you race another driver on a public road, commit a felony using a motor vehicle, or are found guilty of reckless driving three times in one year.
A. suspended
B. denied
C. canceled
D. revoked
Answer:
D
Explanation:
It would be revoked (don't do those things guys!!)
Answer:
D. Revoked
Explanation:
I got it right on FLVS
Two electronics technicians are discussing electronic components. Technician A says that electronic components are color-coded to indicate their electrical values. Technician B says that electronic components are color-coded to indicate their power ratings. Which of the following statements is correct?
A. Neither of the two technicians is correct.
B. Only Technician A is correct.
C. Only Technician B is correct.
D. Both Technician A and Technician B are correct.
Answer:
D. Both Technician A and Technician B are correct.
Explanation:
In electric components, a color code in used on a component to identify their value and function.The value is an electrical value which could be for a resistor or capacitor. For example resistors are coded in ohms.A color code could show the rating of an electric component.For example a tight tolerance resistor will be color coded using three bands.
"How would you direct traffic in the result of a catastrophic earthquake?"
Answer:
In the result of a earthquake, you should direct people into areas that are safe, such as places where the ground has not been broken up, and then tell people to get out of their cars and be careful. You should also have them carry any valuable items out of the car(if they have time), and then wait until the initial shocks and aftershocks are over, and then tell them to get back into their cars and then drive carefully and safely.
Answer:
You would tell people to get out of the way and stay safe.
Two technicians are discussing the intake air temperature (IAT) sensor. Technician A says that the computer uses the IAT sensor as a backup to the engine coolant temperature (ECT) sensor. Technician B says that the powertrain control module (PCM) will subtract the calculated amount of fuel if the air measures hot. Who is correct
Both the technicians are correct.
Explanation
Intake air temperature sensor is used in engines of vehicles to monitor the temperature of air entering the engine.
They are basically made of thermistors whose electrical resistance changes according to temperature.
Depending upon the reading and accuracy of intake air temperature sensor, the power-train control module (PCM) will decide about the air and fuel mixture ratio in the engine.
The hot air in engine requires less fuel to operate the engine parts while cold air requires more fuel to operate the engine.
The ratio of air and fuel mixture should be maintained in the engine and it is done by PCM only after getting the input from IAT. So technician B is saying correct.
Also the IAT works as a backup to support the engine coolant temperature sensor by the computer.
As the IAT checks the temperature of outside air, it will help to change the coolant temperature of the engine based on the environment.
Thus technician A is also correct. So both the technicians are correct.
What is the best way to submit your assignments?
A. Email them to your instructor.
B. Fax them to your instructor.
C. Tell your instructor about them over the phone.
D. Access the Gradebook in the Main Menu.
The best way to submit an assignment is to Email them to your instructor, so Option A is the correct answer.
What are Assignments ?Assignments are the task given by the instructor to make the students learn more about a certain topic .
Assignments help the students to develop the art of researching and creativity along with the development of knowledge in the particular area in which assignment is given.
Assignments should always be submitted on time and a student should never copy his or her assignment.
The best way to submit an assignment is to Email them to your instructor.
To know more about Assignments
https://brainly.com/question/25875756
#SPJ2
How do i fix the ads at the bottom of my TCL tv
Answer:
hit the exit button on your remote
Explanation:
To fix the ads at the bottom of your TCL TV, navigate to the settings menu from the home screen and disable options related to sponsored content, featured content, or advertisements. You might also customize the home screen to reduce ad visibility. If these steps don't work, refer to the owner's manual or contact TCL's customer support.
Explanation:To fix the ads at the bottom of your TCL TV, you might be seeing what is known as Featured Content or sponsored content. This is a common feature on smart TVs, including TCL models, which display advertisements as a way for manufacturers to offset the cost of the TV's smart capabilities.
Here are the steps to try and remove or minimize these ads:
Navigate to your TV's home screen and go into the settings menu.Look for options related to advertising, smart features, or home screen customization.Disable any options related to sponsored content, featured content, or advertisements.If there's an option to customize the home screen, try removing the ad placements or minimizing their visibility.Some TVs may allow you to opt-out of personalized advertising which could reduce the number of ads.Should these steps not work, consider consulting the owner's manual or TCL's customer support for model-specific instructions. Please note that completely removing ads might not be possible on some models where this feature is built into the TV's user interface.
28. Technician A says that during one four-stroke cycle of a cylinder, the crankshaft completes
one revolution. Technician B says that during one four-stroke cycle of a cylinder, the camshaft
completes one revolution. Who is wrong? Explain why?
When your driver license is _____, you will be prohibited from driving for a specified length of time
A. denied
B. suspended
C. revoked
D. canceled
When your driver license is suspended you will be prohibited from driving for a specified length of time
The suspended license implies that your driver's license is temporarily revoked for a set length of time. By meeting certain criteria, you may be able to retrieve your license.
As per Indian country when you are caught speeding, the new law could suspend your license. Along with the suspension of the license, a minimum fine of Rs 1000 can be levied. The fine can be increased based on the car's speed and how far it exceeds the speed limit on that road.If your driving license is suspended, you will be unable to drive for an extended period of time.Therefore, the final answer is "suspended"
Learn more:
brainly.com/question/15254370
What is the best machine to measure the size of cables?
When operating, an instrument measures the total capacitance in the cable and then uses the cable's Mutual Capacitance Coefficient to calculate the cable's length. Capacitance-based measurement instruments can typically measure the length accurate to about 4 percent to 5 percent. i even gave an explanation if u wanted to see how it measures
which pendulum will.mobe faster
Explanation:
The period T (i.e. time to make one complete swing)
of a pendulum of length L is
T = 2 pi sqrt(L/g)
where g=acceleration due to gravity.
Note that the period is independent (to first order) of mass.
This means that the shorter the string, the shorter is the time (i.e. faster) it takes to make a complete swring.
Since the 5 kg mass is attached to a shorter swing, it will "move" faster, or the period T is shorter.
The pendulum from given A and B is pendulum A because it has a shorter thread, Consequently, the left pendulum swings more quickly than the right one.
What is a pendulum?A basic pendulum is a machine in which the point mass is suspended from a fixed support by a light, inextensible string. The mean position of a simple pendulum is represented by a vertical line passing through a fixed support.
The string's length is the variable that needs to be altered. The period of a pendulum is only affected by this one variable, which is also the only one we have easy access to change. The pendulum takes longer to complete one swing the longer the string is.
Therefore, the left pendulum swings more quickly than the right one because the pendulum from given A and B is pendulum A because it has a shorter thread.
To learn more about the pendulum, refer to the below link:
https://brainly.com/question/14759840
#SPJ2
In vehicles equipped with an anti-braking system the drivers foot must remain firmly on the
What is the multiplicity of the root x = -4?
Answer:
See explanation
Explanation:
The multiplicity of a root of a polynomial equation is the number of times the root repeats.
Let [tex]x=a[/tex] be the root of [tex]f(x)[/tex], then;
[tex](x-a)^1=0[/tex] has a multiplicity of 1.
[tex](x-a)^2=0[/tex] has a multiplicity of 2.
[tex](x-a)^3=0[/tex] has a multiplicity of 3.
[tex](x-a)^m=0[/tex] has a multiplicity of m, where m is a positive integer.
We were given the root [tex]x=-4[/tex].
If [tex]f(x)=(x+4)(x-6)^3[/tex]
Then the multiplicity of the root [tex]x=-4[/tex] is 1.
If [tex]f(x)=(x+4)^4(x-6)^3[/tex]
Then the multiplicity of the root [tex]x=-4[/tex] is 4.
Since the polynomial function or equation is not given in the question, we cannot determine the multiplicity of this root.
But I hope with this explanation, you can refer to the original(complete) question and choose the correct answer.
A typical distraction on a rural highway is:
A. Frequently-changing environmental conditions
B. Numerous billboards erected on the roadside
C. Local businesses established on the roadside
D. Pedestrians and non-traditional vehicles on the road